Motorola STARLINE SERIES Manuel d'utilisateur télécharger pdf (Page 1)

Motorola’s 1 GHz STARLINE

series optical node, model

BTN100, leads the industry in features and performance and

is designed to meet the needs of today’s expanding broadband

communication networks. This optical node provides the perfect

solution for system operators who need to deploy ﬁber deeper into

their architecture with the ﬂexibility to expand later. The BTN100

node can be deployed as a low-cost, four output stand alone ﬁber

deep node or to convert an existing BT

ampliﬁer to an optical

node. The base of the BTN100 node is the same as the BT100

ampliﬁer and allows operators to leave the hard line coax cable

installed when segmenting at an ampliﬁer location.

Key Features

The BTN100 Optical Node allows operators to utilize existing BT

ampliﬁer locations. Once converted, the BTN100 allows operators

to seamlessly set up output drive levels of the ampliﬁer for

minimal installation downtime. The BTN is a lower-cost solution to

the SG4000 with a limited feature set. Operators who need the

simplicity of a single receiver and transmitter with four high-level

outputs should look at using the BTN100 node. The BTN100 has

a variety of optical return path transmitters with powers ranging

from 400 µW Isolated Fabry-Perot to 2.0 mW Course Wave

Division Multiplexed transmitters. The BTN100 node allows for

segmentation between the two output ports in the return path.

Forward and Return redundancy is also available with or without

a status monitor. The status monitor is DOCSIS compatible. There

are no conﬁguration boards in the forward path; all changes and

upgrading are conﬁgured through RF cable connections and

jumper settings. In the return path, there is a single return path

conﬁguration board that is used with a simple path to migrate from

a single transmitter to a dual transmitter solution without having

to change any plug-in modules. All BTN100 optical nodes will ﬁt

into the existing BT ampliﬁer and SG2000 installed base, but will

require replacement of the entire lid.

Ampliﬁer and Backward Compatibility

All BTN100 optical nodes will ﬁt into the existing BT ampliﬁer and

SG2000 installed base, but will require replacement of the entire

lid.

Forward Path

High gain levels are capable of achieving +55 dBmV minimum

virtual output level at 1 GHz with a –3 dBm optical input

received power with 4% OMI per channel. Replacing a BT

ampliﬁer with +44 dBmV at 550 MHz output level is easily

achieved with the BT Node.

To further ensure system ﬂexibility, installation ease, and

maintenance, the node is engineered for compatibility with

standard accessories, such as attenuators, automotive fuses,

and FTEC crowbar circuits.

The BTN100 uses modular diplex ﬁlters, which can be

changed for a different frequency split as required. The node

is available with S-split ﬁlters for a 5–40 MHz return and a

52–1003 MHz forward band. K-splits (5–42 MHz/54–1003

MHz), J-splits (5–55 MHz/70–1003 MHz), A-splits (5–65

MHz/85–1003 MHz), and N-split (5–85 MHz/104–1003 MHz)

are also available. These same ﬁlters can be used for all US-

style Motorola RF distribution ampliﬁers (models BLE, MB,

and BT) and nodes (BLN and MBN).

Lid Modules

The receivers and transmitters are the same as the MBN100

Node. The power supply is the same power supply used

in the BT ampliﬁer platform. The DOCSIS transponder is

also the same transponder that is used in the SG4000 and

MBN100 Node platform.

STARLINE BTN100 1 GHZ Optical Node

The BTN100 optical node complements evolving ﬁber-deep networks by

providing operators with a low cost ampliﬁer to node drop in conversion

with ﬂexibility and high performance.

MODEL

BTN100 1

1 GHz OPTICAL NODE STARLINE SERIES

www.amt.com

1 2 3 4 5

Résumé du contenu

Page 1 - BTN100 1

Motorola’s 1 GHz STARLINE® BT® series optical node, model BTN100, leads the industry in features and performance and is designed to

Page 2 - Return Path

STARLINE BTN100 1 GHZ Optical NodeReturn PathRecommended input to the BTN100 node is the same as the BT100 ampliﬁer at +28 dBmV. Five models of trans

Page 3 - BTN100 Block Diagram

STARLINE BTN100 1 GHZ Optical NodeBTN100 Block Diagram ThermJXPLMESWITCHMBN -RX75 ƒ¶JXPSlope BoardLMEJumperJXPJXPJXPJXPJXPPDPDPDPDHILOHILOHILOHILORF

Page 4 - Ordering Information

STARLINE BTN100 1 GHZ Optical NodePart Number Model Description842000-001-00 BTN100/SK4/SSX/ENN BT Node 1 GHz with 5-42 / 54–1003 MHz K-split, 4-outp

Page 5 - Speciﬁcations

OPTICAL RECEIVEROptical Wavelength 1290 – 1600 nm Optical Input Power Range –3.0 to +2.0 dBm continuousOptical Connector Type SC/APC Optical Inp

Plus de documents pour Amplificateurs audio Motorola STARLINE SERIES

Voir le document Motorola STARLINE SERIES Instructions d'exploitation

Motorola STARLINE SERIES Instructions d'exploitation (49 pages)

Voir le document Motorola STARLINE SERIES Manuel d'utilisateur

Motorola STARLINE SERIES Manuel d'utilisateur (6 pages)

Commentaires sur ces manuels

Pas de commentaire

Motorola STARLINE SERIES Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Amplificateurs audio Motorola STARLINE SERIES. BTN100 1 GHz Optical Node STARLINE Series Data Sheet Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Amplificateurs audio Motorola STARLINE SERIES

Commentaires sur ces manuels

Motorola STARLINE SERIES Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Amplificateurs audio Motorola STARLINE SERIES. BTN100 1 GHz Optical Node STARLINE Series Data Sheet Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Amplificateurs audio Motorola STARLINE SERIES

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Motorola STARLINE SERIES