Motorola EM1000 Manuel d'utilisateur télécharger pdf

EM1000 Series

KEM-PK14190-67

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general

safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control

your exposure and ensure compliance with the general population/

uncontrolled environment exposure limits, always adhere to the

following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio

generates measurable RF energy exposure only when transmitting

(in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy

exposure standards and guidelines:

• United States Federal Communications Commission, Code of

Federal Regulations; 47CFR part 2 sub-part J.

• American National Standards Institute (ANSI)/Institute of

Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

• International Commission on Non-Ionizing Radiation Protection

(ICNIRP) 1998.

• Ministry of Health (Canada) Safety Code 6. Limits of Human

Exposure to Radiofrequency Electromagnetic Fields in the

Frequency Range from 3 KHz to 300 GHz, 1999.

• Australian Communications Authority Radiocommunications

(Electromagnetic Radiation—Human Exposure) Standard, 2003.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of

limitation of exposure to electrical, magnetic and electromagnetic

fields in the radio frequency range between 9 KHz and 300GHz” and

“Attachment to resolution #303 from July 2, 2002”.

To ensure optimal radio performance and make sure human

exposure to radio frequency electromagnetic energy is within the

guidelines set forth in the above standards, always adhere to the

following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could

damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding the

antenna affects its effective range.

Body-Worn Operation

To maintain compliances with FCC/Health Canada RF exposure

guidelines if you wear a radio on your body when transmitting

always place the radio in a Motorola-supplied or approved clip

holder, holster, case or body harness for this product. Use of non-

Motorola-approved accessories may exceed FCC/Health Canada RF

exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-

worn accessories and are not using the radio held in the normal use

position, ensure the radio and its antenna are at least 1 inch (2.5

cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or

without an accessory cable, position the radio and its antenna at

least one inch (2.5 cm) from the body.

Approved Accessories

For a list of approved Motorola accessories, visit our Web site at

www.motorola.com.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,

designed or otherwise configured for electromagnetic compatibility.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts,

turn off your radio in any facility where posted notices instruct you

to do so. Hospitals or health care facilities may be using equipment

that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an

aircraft. Any use of a radio must be in accordance with applicable

regulations per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends that a

minimum separation of 6 inches (15 cm) be maintained between a

handheld wireless radio and a pacemaker. These recommendations

are consistent with the independent research by and

recommendations of the U.S. Food and Drug Administration.

People with pacemakers should:

• ALWAYS keep the radio more than 6 inches (15 cm) from their

pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the potential

for interference.

• Turn the radio OFF immediately if there is any reason to suspect

that interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing aids.

In the event of such interference, you may want to consult your

hearing aid manufacturer to discuss alternatives.

Medical Devices – Other

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to assist you in

obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the

area where you drive, and always obey them. If you do use your

radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call if

driving conditions so require.

The use of a two-way radio while engaged in activities requiring

concentration may cause distraction or otherwise impair your

ability to safely participate in such activities. Always use technology

safely.

Do not place a portable radio in the area over an air bag or in the

air bag deployment area. Air bags inflate with great force. If a

portable radio is placed in the air bag deployment area and the air

bag inflates, the radio may be propelled with great force and cause

serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially qualified

should be used in such areas as “Intrinsically Safe.” Do not remove,

install or charge batteries in such areas. Sparks in a potentially

explosive atmosphere can cause an explosion or fire resulting in

bodily injury or even death.

For More Information

For further information, you may call Motorola at 1-800-638-5119

(U.S. and Canada), or e-mail us at giantintl@callcenter.com or visit

us on the Internet at www.motorola.com.

Note: The areas with potentially explosive atmospheres referred to

above include fueling areas such as below decks on boats, fuel or

chemical transfer or storage facilities, areas where the air contains

chemicals or particles (such as grain, dust or metal powders) and

any other area where you would normally be advised to turn off your

vehicle engine. Areas with potentially explosive atmospheres are

often—but not always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your

radio when you are near electrical blasting caps, in a blasting area,

or in areas posted “Turn off two-way radios.” Obey all signs and

instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a

damaged antenna comes into contact with your skin, a minor burn

can result.

Batteries

All batteries can cause property damage and/or bodily injury such as

burns if a conductive material—like jewelry, keys or beaded chains—

touch exposed terminals. The conductive material may complete an

electrical circuit (short circuit) and become quite hot. Exercise care in

handling any charged battery, particularly when placing it inside a

pocket, purse or other container with metal objects.

Exercise care when removing NiMH or AA batteries. Do not use

sharp or conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has received a

sharp blow, or has been dropped or damaged in any way.

3. Never alter the AC cord or plug provided with the unit. If the

plug will not fit the outlet, have the proper outlet installed by a

qualified electrician. An improper condition can result in a risk

of electric shock.

4. To reduce the risk of damage to the cord or plug, pull the plug

rather than the cord when disconnecting the charger from the

AC receptacle.

5. To reduce the risk of electric shock, unplug the charger from the

outlet before attempting any maintenance or cleaning.

6. Use of an attachment not recommended or sold by Motorola

may result in a risk of fire, electric shock or personal injury.

7. Make sure the cord is located so it will not be stepped on,

tripped over or subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could result in a

risk of a fire and/or electric shock. If an extension cord must be

used, make sure that:

• The pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the charger.

• The extension cord is properly wired and in good electrical

condition.

• The extension cord size is 18 AWG for lengths up to 100 feet,

and 16 AWG for lengths up to 150 feet.

9. The supply cord of the AC adaptor cannot be replaced. If the

cord is damaged, call customer service at 1-800-638-5119 (U.S.

and Canada) or e-mail us at giantintl@callcenter.com.

FCC Licensing Information

Your Motorola radio operates on General Mobile Radio Service

(GMRS) frequencies and is subject to the Rules and Regulations of

the Federal Communications Commission (FCC). The FCC requires

that all operators using GMRS frequencies obtain a radio license

before operating their equipment. To obtain the FCC forms, please

request Form 605 and 159 , which includes all of the forms and

instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

You may also visit the FCC’s Web site at www.fcc.gov.

Changes or modifications not expressly approved by Motorola may

void the user’s authority granted by the FCC to operate this radio

and should not be made. To comply with FCC requirements,

transmitter adjustments should be made only by or under the

supervision of a person certified as technically qualified to perform

transmitter maintenance and repairs in the private land mobile and

fixed services as certified by an organization representative of the

user of those services. Replacement of any transmitter component

(crystal, semiconductor, etc.) not authorized by the FCC equipment

authorization for this radio could violate FCC rules.

3. Gently remove each battery by easing each battery out individually.

4. Reposition the battery cover and press down to secure.

Notes

• Exercise care when removing NiMH or AA batteries. Do not use

sharp or conductive tools to remove either of these batteries.

• Remove the batteries before storing your radio for extended

periods of time. Batteries corrode over time and may cause

permanent damage to your radio.

Using the Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for

NiMH batteries and can be placed on any flat surface, such as a

desk or workbench. Charge the NiMH battery overnight (at least 16

hours) before using it for the first time. After the initial charge, an

empty battery is fully charged within 14 hours.

1. Follow the steps above to install a NiMH Battery Pack.

2. Plug the AC power supply cord into the jack on the desk stand.

3. Plug the AC power supply into a standard wall outlet.

4. With a radio facing forward, slide it into one of the charging

pockets.

5. When charging in the battery charger, the red light on the

charger base will glow continuously.

Using the mini-USB Charging Connector

The mini-USB charging connector is a handy port that allows you to

conveniently charge your NiMH battery pack. This is an alternative

to charging your NiMH battery pack in the Battery Charger desk

stand using the AC wall adaptor and especially useful when used

while traveling.

Available mini-USB charging options: (optional accessories)

1. Wall travel charger

2. Vehicle charger

3. Mini-USB computer cable

If using a computer, the computer must be turned on.

This and other accessories (sold separately) are available for your

radio. For more information, visit our Web site at

www.motorola.com or shop.giantintl.com.

1. Plug your mini-USB cable or charger into a power source as is

appropriate for your accessory.

2. Plug the cable into the mini-USB port on the bottom of your radio.

3. An empty battery will be fully charged in 14 hours.

4. The LED indicator light on the radio will glow to indicate that the

battery is charging.

Notes

• The light will remain red after the NiMH battery pack is fully

charged.

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery temperature

acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger within

16 hours. Do not store the radio while connected to the charger.

• Turn radio off while charging.

Attaching and Removing the Belt Clip

1. Attach belt clip to pocket or belt strap.

2. Align the belt clip post with the hole in the back of the radio.

3. Gently push until the clip clicks in place.

To Remove

1. Push down on the release tab at the top of the belt clip to

release the catch.

2. Pull the belt clip away from the back of the radio.

Turning Your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to

turn the radio off.

1. In the ON position, the radio chirps and briefly shows all feature

icons available on the radio.

2. The display screen then shows the current channel, code and

all features that are enabled.

Setting the Volume

Press and hold for three seconds while rotating until you

reach a comfortable listening level.

1. Rotate clockwise to increase the volume.

2. Rotate counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Talking and Listening

To communicate, all radios in your group must be set to the same

channel and Interference Eliminator Code.

1. To talk, press and hold .

2. When you are finished talking, release .

For maximum clarity, hold the radio two to three inches away from

your mouth and speak directly into the microphone. Do not cover

the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet apart.

Monitor Button

Pressing and holding for three seconds allows you to listen to

the volume level of the radio when you are not receiving. This allows

you to adjust the volume, if necessary. You can also press to

check for activity on the current channel before you talk.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the radio

emits a continuous warning tone and stops transmitting if you

press for 60 continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. Channels 8-14 are FRS 0.5 watt only and

all other channels are GMRS (See the "Channels and Frequencies"

table on overleaf for details).

1. With the radio on, press . When the radio is on a 0.5

watt channel, displays. When the radio is on a 1.5 watts

channel, displays. The current channel flashes.

2. Press or and select an unused or quiet channel.

3. Press to save the channel setting or to continue set up.

Selecting The Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has 121

Interference Eliminator Codes. Codes 1 – 38 are the standard analog

codes that appear on other FRS/GMRS radios. Codes 39 – 121 are

additional digital codes added for superior interference protection.

0 is the off position, no analog or digital codes are enabled.

To set the code for a channel:

1. Press until the code starts to flash.

2. Press or to select the code.

3. Press to save the code setting or to continue set up.

You can set a different code for each channel using this procedure.

An extended press of or allows you to scroll through the

Interference Code rapidly so you can quickly reach the code you

want.

Note: You must set the Interference Eliminator Code to 0 on a radio

that uses Interference Eliminator Codes to communicate with radios

that do not have Interference Eliminator Codes. Select 0 for “no

tone, no code” and OFF will flash on your radio’s display.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in your

group so you can alert them that you want to talk. You have 10 call

tones from which to choose.

To set a call tone:

1. With the radio on, press three times until the current

call tone setting (0 - 10) flashes and appears.

2. Press or to change and hear the call tone.

3. Press to set the new call tone or to continue set up.

To transmit your call tone to other radios set to the same channel

and Interference Eliminator Code as your radio, press .

Note: Setting the call to 0 disables the call tone feature.

Hands-Free Use Without Accessories ( )

You can use the iVOX feature to transmit hands-free without the need

for any headset accessories. Once iVOX is turned on, the radio detects

your voice and transmits when you speak into the internal microphone.

1. Press until appears on the display. The current

setting On/Off will flash.

2. Press or to select On or Off.

3. Press to set or to continue set up.

Hands-Free Use With Accessories ( )

You can transmit hands-free more reliably with the use of optional

headset accessories. Once VOX is turned on, the radio detects your

voice and transmits when you speak.

Many accessories (sold separately) are available for your radio. For

more information, visit our Web site at www.motorola.com or

shop.giantintl.com.

1. Turn the radio off and plug the VOX accessory into the

accessory port.

2. Turn the radio on. VOX shows on the display.

3. Adjust the volume appropriately by rotating . Lower the

volume before placing the accessory on your head or in your ear.

4. To turn off, simply remove accessory.

Note: There is a short delay between the time you start talking and

when the radio transmits. There is a short delay before the

transmission is completed.

Display Screen Guide

Numbers for Channel,

Call Tone

Numbers for Codes

— Battery Meter

— Channel Power

Indicator (see Menu

Options)

— Lock

— Talk Confirmation

Tone (Roger Beep)

— Noise Filtering

— On/Off for each

feature

— Scan

— Call Tone,

Keypad Tone

— Weather Alert

— Hands-Free Use

Without

Accessories

— Hands-Free Use

With Accessories

Continued on back

EM1000

Control Buttons

Volume

Push to Talk

Flashlight Button

Microphone

Call Tone

Scroll/Weather

Flashlight LED

Emergency Alert

LED Indicator

Accessory Jack

Menu/Lock

Scan/Monitor

Mini-USB

Charging Port

Getting Started

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or 3

AA alkaline batteries and beeps when the batteries are low.

Installing NiMH Rechargeable Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover latch

up and remove the cover.

3. Remove the battery pack from the clear plastic bag (Do not

disassemble or unwrap the battery pack).

4. Insert the NiMH battery pack with the diagram facing you.

5. Reposition the battery cover and press down to secure.

Installing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover latch

up and remove the cover.

3. Insert the three AA alkaline batteries with + and - polarity as

shown inside.

4. Reposition the battery cover and press down to secure.

Radio Battery Meter

The radio battery icon shows the battery charge level, from full

to empty . When the radio has one segment left, the

radio chirps periodically or after releasing (Low Battery Alert).

Removing the NiMH Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

3. Remove the NiMH battery pack by pulling the ribbon attached to

the radio.

4. Reposition the battery cover and press down to secure.

Removing the Three AA Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

For a fax:

Contact the

Fax-0n-Demand

system

For mail service:

Call the FCC

Forms Hotline

If you have

questions about

the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM

(3676)

1-888-CALL-FCC

(225-5322)

Two-Way Radio

User’s Guide

1 2

Two-Way Radio 1

Résumé du contenu

Page 1 - Two-Way Radio

EM1000 SeriesKEM-PK14190-67Safety and General InformationImportant Information on Safe and Efficient OperationRead This Information Before Using Your

Page 2

Setting the Sensitivity Level When in or ModeAdjusting the radio’s sensitivity level helps minimize the possibilityof unintended noises triggering a t

Commentaires sur ces manuels

Pas de commentaire

Motorola EM1000 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour bateaux Motorola EM1000. Motorola EM1000 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour bateaux Motorola EM1000