Motorola MotoWI4 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Passerelles et répétiteurs Motorola MotoWI4. Motorola MotoWI4 User's Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 246
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs

Résumé du contenu

Page 1 - User Guide

PTP 600 SeriesUser Guide MOTOROLA POINT-TO-POINT WIRELESS SOLUTIONS

Page 2

88.1 Home Page – PTP 600 Series Bridge...68 8.1.1 Home Page Alarm

Page 3 - MOTOROLA, Inc

98The detailed counters page is subdivided into two columns. Column one presents the detailed statistics for the bridge’s Ethernet interface. Column

Page 4 - Deployment and Operation

99Tx Multicasts: Total number of good multicast packets. Tx Collisions: Total number frames experiencing collisions. Tx 64 Bytes: Total number 64 by

Page 5

100 Example PTP 600 Series Configuration DataFor your convenience these two units have been pre-configured as a link Units:ODU serial number ODU se

Page 6

1018.3.4.1 Manually Configuring The Wireless Units If the installer / system administrator wishes, they may modify the default installation configu

Page 7 - Disclaimer

102 A license key is programmed into each unit during production and can be found written on the Configuration Data Summary Label which is attached

Page 8

103IP Address: Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify this unit on a network.

Page 9

104Once complete, click the ‘Submit Internet Protocol Configuration’ button or the ‘Next’ link. 8.3.4.3 Telecoms Interface If the telecoms interface

Page 10

105Telecoms Channel Selection: This controls the selection of the telecoms interface standard supported options or T1 and E1. Channel A Line Code: T

Page 11

106 Target MAC Address: The MAC Address of the peer unit that will be at the other end of the wi

Page 12

107Spectrum Management Control: Is used to configure the PTP 600 Series Bridge’s Spectrum Management features, see section 8.3.7 for more details.

Page 13

98.3.10.3 SNMP Configuration...134 8.3.10.

Page 14

108 Figure 49 - Fixed Frequency Operation

Page 15 - List of Figures

109Installation Tones: Where the use of audio installation tones is not required this control allows the installer to optionally disable the tone g

Page 16

110If the settings are correct and appropriate, click the “Confirm Configuration, Arm Installation and Reboot” button. The user will now be prompted

Page 17

1118.3.4.5 Disarm Step 5 of the installation wizard is the disarm phase. Figure 52 - Disarm Installation

Page 18

112Once section 8.3.4.4 is complete pressing the “Disarm Installation Agent” button completes the installation process22 and the audible installatio

Page 19 - List of Equations

113After installation the system administrator may wish to modify the wireless units descriptive configuration (link name and link location). In add

Page 20

114The screen displays the receive power over the last three minutes. This will allow the installer to slowly sweep the antenna during installation

Page 21 - 1 About This User Guide

115The ‘Fixed’ or ‘Recovery’ image is used by the System Administrator to: • Reset Ethernet configuration to default settings • Erase Configuration

Page 22

116The user should ensure that the correct image is shown before pressing the “Program Software Image into Non-Volatile Memory” button. Once this bu

Page 23 - 1.3 Sending Feedback

117When the software image has been written to non-volatile memory Figure 59 will be displayed showing the status of the software upload. Reboot the

Page 24 - 2 Avoiding Hazards

1013 PTP 600 Series Bridge – Connectorized Model ...171 13.1 Scope ...

Page 25 - 1. Calculated

1188.3.7.1 Wireless Channels The PTP 600 Series Bridge operates using a set of predefined overlapping channels. There are a different number of chan

Page 26 - 3 Getting Started

119 Peak of Means is the largest mean interference measurement encountered during the quantizati

Page 27 - 3.2 Welcome

120All configuration changes are applied at the master only. These changes are then messaged from the master to the slave. Any Spectrum Management c

Page 28

121 Figure 62 - Spectrum Management as seen from the Slave Figure 61 shows an example Spectrum Management webpage as seen from the master. Figure 6

Page 29 - 3.3 Product Description

1228.3.7.5 Spectrum Management Configuration The following section describes the user modifiable configuration accessible from the Spectrum Managem

Page 30

1238.3.7.6 Barring Channels Channels can only be barred / unbarred by the system administrator from the master Spectrum Management web page. The bar

Page 31

124The X-axis shows a stylized view of the 9 or 10 selectable wireless channels. It is important to note that adjacent channels on the display have

Page 32

125The top of the colored bar represents the 99.9% percentile metric for specific channel. The ‘I’ Bar is used to display the mean of means and peak

Page 33

1268.3.7.9 Viewing Historic Spectrum Management Metrics Spectrum Management allows the system administrator to view the results of previous measure

Page 34

1278.3.8 Spectrum Management (Fixed Frequency and WIMAX) The PTP 600 Series Bridge software allows a user to optionally fix transmit and receive fr

Page 35

1114.5 Customer Cable Termination ... 196 14.6 Lightnin

Page 36

128Channel barring is disabled in fixed frequency mode; it is not required as dynamic channel hopping is prohibited in this mode. The only controls

Page 37

129 Figure 67 - Spectrum Management Help Page (Fixed Frequency) 8.3.9 Spectrum Management Control - With Operational Restrictions When operating w

Page 38 - 3.4 Warranty

130used to host the wireless link, but CAC measurements are still taken so that adjacent channel biases can be calculated correctly and so the user

Page 39 - 4 Product Architecture

131 Figure 69 - Spectrum Management Slave Screen With Operational Restrictions The colored bar represents the following channel state: Green Activ

Page 40

132Table 13 - Spectrum Management Change State Key With Operational Restrictions 8.3.10 Remote Management Page The Remote Management page (Figure 7

Page 41 - 5 General Considerations

1338.3.10.1 SNMP (Simple Network Management Protocol) The industry standard remote management technique is SNMP (Simple Network Management Protocol

Page 42 - 5.2 Region Codes

1348.3.10.3 SNMP Configuration SNMP State: The SNMP state attribute controls the creation of the SNMP features. Changing the SNMP state attribute re

Page 43 - 5.3 Operational Restrictions

135SMTP Port Number: The SMTP Port Number is the port number used by the networked SMTP server. By convention the default value for the port number

Page 44

136Set Date: Displays the current date. The year, month and day can be set using the drop-down selection boxes. Time Zone: See section 8.3.10.6. Day

Page 45

137For example, when histogram 1 fills up and starts to overflow the first minute of overflow is analyzed and the maximum, minimum and mean over tha

Page 46

1221.1.3 Management ...237 21.1

Page 47 - 5.5 Distance

138The histograms that are available are: • Vector Error • Rx Power • Tx Power • Signal Strength Ratio • Link Loss • Rx Data Rate • Tx Data Rate

Page 48 - 5.7 Lightning Protection

139The following diagnostics are available: • Vector Error • Rx Power • Tx Power • Signal Strength Ratio V/H • Link Loss • Rx Data Rate • Tx Data

Page 49 - 6 Site Planning

140 To change the password any combination of alphanumeric characters, up to 31 characters in length, can be used. 8.3.13 License Key The License

Page 50

141The user must enter the license key and click the ‘Validate License Key’ button to check that the key is valid and program it to non-volatile mem

Page 51

1428.3.14 Properties The web page properties screen allows the user to configure the web page interface. Figure 77 - Properties WEB Properties: Dis

Page 52

1438.3.15 Reboot The reboot page allows the system administrator to perform commanded reboots of the wireless unit. The reboot page also allows the

Page 53 - 7 Installation

1449 Recovery Mode The Motorola PTP 600 point-to-point wireless Ethernet bridges have a special mode of operation that allows the user to recover a

Page 54 - 7.6 Mounting the ODUs

145Clicking on the warning page image will take the user on to the Recovery Option Page (Figure 81). Figure 81 - Recovery Options Page The recovery

Page 55

146Erase Configuration: This allows the user to erase the unit’s entire configuration. Executing this option will also erase factory settings such a

Page 56 - 7.7 Connecting Up

147When the download is complete a page is displayed indicating the status of the software download (Figure 83). Figure 83 - Software Download Com

Page 57

13List of Figures Figure 1 - Typical PTP 600 Series Bridge Deployment...27 Figure 2

Page 58

1489.2 Reset IP & Ethernet Configuration To reset IP & Ethernet configuration back to factory defaults the user should press the “Reset IP

Page 59

149The user will now be presented with a pop up box asking them to confirm the action (Figure 87) Figure 87 - Reboot Confirmation Pop Up The unit w

Page 60

150On confirmation the following page will be displayed (Figure 89). The user should now reboot the unit by pressing the “Reboot” button. Figure 89

Page 61

151The user will now be presented with a pop up box asking them to confirm the action (Figure 90) Figure 90 - Reboot Confirmation Pop Up The unit w

Page 62

1529.4 Reboot To erase the unit’s configuration the user should press the “Reboot” button on the “Recovery Options” page (Figure 81). The user will

Page 63

15310 Fault Finding If communication has been lost with the unit at the near end of the link then there may be a hardware fault with the wiring, net

Page 64

154If neither is illuminated then there is no voltage on the power wires to the ODU. • Check that the mains power is connected and switched on.

Page 65

155Power Indoor Unit LED check chart: Mode Green LED Yellow LED No Ethernet Cable Connected Yellow LED Ethernet Cable Connected between PIDU Plus a

Page 66

1565. Ensure that there is greater than 100K ohms between pin 1 and ODU ground for all cable lengths. 6. Ensure that there is greater than 100K oh

Page 67

157• Check License key • Check Master Slave • Check that the link has not been further obscured or the ODU misaligned. • Check the DFS page at e

Page 68 - 8 Web Page Reference

14Figure 36 - Save and Restore Configuration Page ...87 Figure 37 - Save

Page 69

15811 Lightning Protection EMD (Lightning) damage is not covered under warranty The recommendations in this user manual when installed correctly g

Page 70

159The following diagrams (Figure 93 & Figure 94) show this zoning pictorially: Equipment mounted in Zone A should be capable of carrying the f

Page 71

160 Figure 93 - ODU mounted in Zones A & B Figure 94 - Showing how the use of a Finial enables the ODU to be mounted inside Zone B

Page 72

161 Zone A Zone B Earth ODU Mandatory Mandatory Screen Cable Mandatory Mandatory Surge Arrestor Unit at ODU – ALPU-ORT Mandatory Mandatory Ea

Page 73

162A typical installation is shown in Figure 96 and Figure 97. Note: Grounding Points are shown unprotected for clarity. Grounding points should be

Page 74 - 8.2 Systems Status Page

163 Figure 97 - Lower Grounding Configuration

Page 75

164An Andrew Grounding Kit and Surge Arrestor Unit must be located at the ODU and reliably grounded as shown in Figure 95. There may also be a regul

Page 76

165 Figure 98 - Surge Arrestor ALPU-ORT Connection Illustration Note: Cable screens have been sleeved.

Page 77

16611.3 Testing Your Installation If you have followed the above instructions you will have wired your system to the following diagram: Figure 99

Page 78

167The Ethernet LED flashes ten times but irregularly Irregularly flashing, seen as a short gap followed by a long gap, indicates that the ODU has b

Page 79

15Figure 73 - Password Change...139 Figure

Page 80

16812 Wind Loading 12.1 General Antennas and electronic equipment mounted on towers or pole mounted on buildings will subject the mounting structure

Page 81

169 Lateral Force (kg) at wind speed (m/s) Largest Surface Area (sq m) 30 40 50 60 70 PTP 600 Series Bridge - Integrated 0.130 12 22 34 49 66 PTP

Page 82

170Chicago, Illinois 87 Hatteras, North Carolina 110 Miami, Florida 132 New York, New York 99 Pensacola, Florida 114 UK Meteorological Office,

Page 83

17113 PTP 600 Series Bridge – Connectorized Model 13.1 Scope This section details the changes and additional features relevant to the connectorized

Page 84

172 13.2.2 Antenna Choices – 5.8 GHz The integrated antenna has a gain of 23 dBi. In non-FCC regions antenna choice is not restricted but any regio

Page 85

17313.3 Software/Features The variant operates in the same way as the basic 600 Series bridge and is released initially with the feature set of the

Page 86

17413.3.2 Configuration Pages The amended Configuration web page is shown below as Figure 102. Figure 102 - Connectorized 600 Series bridge ‘Syste

Page 87

17513.3.3 Installation Pages The installer is prompted to enter the Antenna Gain and Cable Loss (Connectorized PTP 600 Series Bridge to antenna) at

Page 88

176Antenna Gain: Gain of the antenna you are connecting to the unit, see Table 21. Cable Loss: Loss in the cable between the ODU and the antenna. No

Page 89

177 Figure 104 - Connectorized 600 Series bridge ‘Confirm Installation’ Page EIRP The Confirm Installation Page displays the EIRP (Effective Isotro

Page 90

16Figure 110 - Polyphaser Assembly...190 Figure 11

Page 91

178 Figure 105 - Connectorized 600 Series bridge ‘Disarm Installation’ Page

Page 92

17913.4 Deployment Considerations The majority of radio links can be successfully deployed with the 600 Series bridge. It should only be necessary

Page 93

180The antennas which can be deployed with the Connectorized 600 Series Bridge are shown in Table 21. 13.6.2 Cable Losses (FCC Regions Only) The

Page 94

181Manufacturer Antenna Type Gain (dBi) Flat Plate Parabolic Dish RFS RFS 1-foot Flat Panel, MA0528-23AN (23dBi) 23 Y RFS RFS 2-foot Flat Pane

Page 95

182Manufacturer Antenna Type Gain (dBi) Flat Plate Parabolic Dish Gabriel Gabriel 4-foot Standard Dual QuickFire Parabolic, QFD4-52-N 34.7 Y Gabri

Page 96

18313.8 Installation The section covers the generic installation instructions for the Connectorized versions of the PTP 600 Series point-to-point wi

Page 97

18413.8.4 Miscellaneous supplies The following miscellaneous supplies will be required: • Cable ties, cable cleats – for securing cables • Self-am

Page 98

18513.8.7 Alignment Process When aligning antennas deployed with a Connectorized 600 Series bridge unit it may not be possible to hear the alignment

Page 99

18613.8.10 Completing the Installation The installation should be completed by checking all mounting nuts bolts and screws, securing all cables and

Page 100

187All joints should be weatherproofed using self-amalgamating tape. It is recommended that a layer of PVC tape be placed over the self-amalgamating

Page 101

17List of Tables Table 1 - Font types...

Page 102

18813.9 Additional Lightning Protection The following guidelines should be applied in addition to those described in Section 11 ”Lightning Protectio

Page 103

18913.9.2 ODU Mounted Indoors Where the ODU is mounted indoors, lightning arrestors should be deployed where the antenna cables enter the building

Page 104

190The lighting arrestors should be ground bonded to the building ground at the point of entry. Motorola recommends Polyphaser LSXL-ME or LSXL light

Page 105

19114 E1/T1 Installation Guide 14.1 Preparing the PTP 600 Series Bridge E1/T1 Cable Note: The maximum cable length between the ODU and the customer

Page 106

192This procedure applies to the ODU termination. The above procedure should be repeated for the customer equipment end of the cable when the cable

Page 107

19314.2 Making the Connection at the ODU Looking at the back of the unit with the cable entry at the bottom, the PTP 600 Series Bridge E1/T1 connec

Page 108

194The following procedure describes how connection is made at the ODU. It is often easier to carry out this procedure on the ground or a suitable s

Page 109

195Should it be necessary to disconnect the E1/T1 cable at the ODU this can be achieved by removing the weatherproofing gland and depressing the RJ4

Page 110

19614.3 Routing the Cable After connecting the cable to the ODU it can be routed and secured using standard cable routing and securing techniques.

Page 111

197 Figure 116 - Diagrammatically Showing the E1-T1 Connections

Page 114

19814.6 Lightning Protection 14.6.1 Overview Section 11 in the main body of this manual contains the requirements for the Motorola PTP 600 Series d

Page 115

199 Figure 117 - Typical Mast Installation with the addition of the E1-T1 cable

Page 116

200Note: There may be a local regulatory requirement to cross bond the CAT 5 drop cable at regular intervals to the mast. This may be as frequent as

Page 117

20114.7 Surge Arrestor Wiring An Andrew Grounding Kit and Surge Arrestor Unit must be located at the ODU and reliably grounded as shown in Figure 9

Page 118

202 Figure 119 - Surge Arrestor ALPU-ORT Connection Illustration

Page 119

20314.8 Testing Your Installation If you have followed the above instructions you will have wired your systems to the following diagram: Figure 12

Page 120

204 CAT-5 Length (Meters) Resistance between pins 3 & 6 and pins 7 & 8 (ohms) Resistance between pins 1 & 2 and pins 4 & 5 (ohms)

Page 121

20515 Data Rate Calculations To aid the calculation of data rate throughput, the following plots of throughput verses link range have been produced

Page 122

206 Figure 123 - QPSK 0.87 Single Paylaod Figure 124 - 16 QAM 0.63 Single Payload Figure 125 - 16 QAM 0.87 Single Paylaod

Page 123

207 Figure 126 - 64 QAM 0.75 Single Payload Figure 127 - 64 QAM 0.92 Single Payload Figure 128 - 256 QAM 0.81 Single Payload

Page 124

191 About This User Guide This guide covers the installation, commissioning, operation and fault finding of the Motorola PTP 600 Series of Point-to

Page 125

208 Figure 129 - 16 QAM 0.63 Dual Payload Figure 130 - 16 QAM 0.87 Dual Payload Figure 131 - 64 QAM 0.75 Dual Payload

Page 126

209 Figure 132 - 64 QAM 0.92 Dual Payload Figure 133 - 256 QAM 0.81 Dual Payload

Page 127

21016 AES Encryption Upgrade The Motorola PTP 600 Series bridges support link encryption using the NIST approved Advanced Encryption Standard, HFIP

Page 128

211Option 1 allows the user to encrypt all traffic sent over the wireless link using 128-bit encryption. Option 2 allows the user to encrypt traffic

Page 129

212Figure 134 shows the license key data entry screen. This screen can only be accessed by the system administrator. If you do not have access to th

Page 130

21316.1.2 Encryption Mode and Key Entering the license keys only does not initialize AES link encryption. Link encryption can only be enabled via t

Page 131

2146. Reboot both ends of the link Figure 136. The software is designed to allow five seconds so that a user can command both ends of the link to r

Page 132

21517 Legal and Regulatory Notices 17.1 Important Note on Modifications Intentional or unintentional changes or modifications to the equipment mus

Page 133

216 Table 26 - US FCC IDs and Industry Canada certification numbers Where necessary, the end user is responsible for obtaining any National lic

Page 134

217The relevant Declaration of Conformity can be found at www.motorola.com/ptp European Union (EU) Waste of Electrical and Electronic Equipment (WE

Page 135

20This document also employs a set of consistently used admonitions. Each type of admonition has a general purpose that underlies the specific infor

Page 136

21817.3 National and Regional Regulatory Notices – 5.4 GHz Variant 17.3.1 U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Not

Page 137

219Where necessary, the end user is responsible for obtaining any National licenses required to operate this product and these must be obtained befo

Page 138

220The relevant Declaration of Conformity can be found at www.motorola.com European Union (EU) Waste of Electrical and Electronic Equipment (WEEE)

Page 139

22117.4 Exposure See Preventing Overexposure to RF on Page 22. 17.5 Legal Notices 17.5.1 Software License Terms and Conditions ONLY OPEN THE PACKA

Page 140

222Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the Software and any copies, including tra

Page 141

223THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY MOTOROLA, AND MOTOROLA AND ITS LICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EITHER E

Page 142

224Transfer. In the case of software designed to operate on Motorola equipment, you may not transfer the Software to another party except: (1) if yo

Page 143

225Disputes. You and Motorola hereby agree that any dispute, controversy or claim, except for any dispute, controversy or claim involving intellectu

Page 144

22618 Glossary ARP Address Resolution Protocol NLOS non-Line-of-Sight ARQ Automatic Repeat reQuest ODU Outdoor Unit BPSK Binary Phase S

Page 145

22719 FAQs Can I source and use my own PoE adaptor with the 600 Series bridge? No. The 600 Series bridge uses a non-standard PoE configuration. Fai

Page 146 - 9 Recovery Mode

211.2 Getting Additional Help To get information or assistance as soon as possible for problems that you encounter, use the following sequence of a

Page 147

228Why does the 600 Series bridge operate in the 5GHz band? The 5 GHz band offers the dual benefits of high data throughput and good radio propagati

Page 148 - 9.1 Upgrade Software Image

229How will my investment be protected as new features are developed? Future enhancements can be downloaded to the unit, meaning advances in technol

Page 149

23020 Index Alarm ...67, 68 Alignment...62, 184 antenn

Page 150

23121 Specifications 21.1 System Specifications 21.1.1 Wireless 5.4GHz Variant Radio Technology Specification RF Band 5.470-5.725GHz Channel

Page 151 - 9.3 Erase Configuration

232The receive sensitivities and system gains for each mode are as follows: Mode Receive Sensitivity (dBm) Transmit Power (dBm) Link Budget (dB) BPS

Page 152

233 Antenna Antenna Type Integrated flat plate antenna Antenna Gain 23 dBi typical Antenna Beamwidth 8 Degrees Wireless PHY Max Path Loss 161 d

Page 153

23421.1.2 Wireless 5.8GHz Variant Radio Technology Specification RF Band 5.725-5.850GHz Channel Selection By dynamic frequency control and man

Page 154 - 9.4 Reboot

235The receive sensitivities and system gains for each mode are as follows: Mode Receive Sensitivity (dBm) Transmit Power (dBm) Link Budget (dB) BPS

Page 155 - 10 Fault Finding

236 Antenna Antenna Type Integrated flat plate antenna Antenna Gain 23 dBi typical Antenna Beamwidth 8 Degrees Wireless PHY Max Path Loss 161 d

Page 156

23721.1.3 Management Management Power status Ethernet Link Status Status Indication Data activity Web server and browser for setup Audio tone

Page 157

222 Avoiding Hazards 2.1 Preventing Overexposure to RF Energy Caution To protect from overexposure to RF energy, install the radios for the 600 fami

Page 158 - 10.2 Radio

23821.1.4 Physical Physical Integrated Dimensions Width 14.5” (370mm), Height 14.5” (370mm), Depth 3.75” (95mm) Weight 12.1 lbs (5.5 Kg) includ

Page 159

23921.2 Safety Compliance 21.2.1 5.4 GHz Variant Region Specification USA UL 60950 Canada CSA C22.2 No.60950 International CB certified & cer

Page 160 - 11 Lightning Protection

24021.3 EMC Emissions Compliance 21.3.1 5.4GHz Variant Region Specification USA FCC Part 15 Class B Canada CSA Std C108.8, 1993 Class B Europe E

Page 161 - 11.2 Detailed Installation

24121.4 EMC Immunity Compliance Top-level Specification ETSI 301-489. Specification Comment EN 55082-1 Generic EMC and EMI requirements for Euro

Page 162

24221.5 Radio Certifications 21.5.1 5.4GHz Variant Region Specification (Type Approvals) USA FCC Part 15.407 EU EN301 893 V1.2.3/V1.3.1 CANADA

Page 163

24321.7 System Connections 21.7.1 PIDU Plus to ODU and ODU to Network Equipment Connections Figure 137 - Cable Connection Diagram (T568B Color C

Page 164

244 Unit A1, Linhay Business Park Eastern Road, Ashburton Devon, TQ 13 7UP, UK Telephone Support: +1 877 515-0400 www.motorola.com/p

Page 165

23Peak power density in the far field of a radio frequency point source is calculated as follows: Where S = power density in W/m2

Page 166

243 Getting Started 3.1 For Your Safety WARNING: Use extreme care when installing antennas near power lines. WARNING: Use extreme care when worki

Page 167

25CAUTION: Safety will be compromised if external quality cables are not used for connections that will be exposed to the weather. CAUTION: Safety

Page 168

263.2.3 Contact Information Postal Address: Motorola, Inc. Unit A1, Linhay Business Park, Eastern Road, Ashburton, Devon. TQ13 7UP United Kingdom

Page 169

273.3 Product Description This User Manual is specifically written for the 600 family of point-to-point broadband wireless solutions. The PTP 600 Se

Page 170 - 12 Wind Loading

1MOTOROLA, Inc. Point-to-Point Wireless Bridges – PTP 600 Series Software Release PTP 600-04-01 System User Manual June 18th, 2007 Ref: PHN-0896-

Page 171 - 12.4 Wind Speed Statistics

28Each end of the link consists of: • An integrated outdoor transceiver unit containing all the radio and networking electronics hereafter referre

Page 172

29Alternately, the network connection to a PTP 600 Series Bridge can be made using a 1000BaseSX Fiber Optic cable connected directly to the ODU. In

Page 173 - 13.2 Product Description

303.3.2 PIDU Plus – PTP 600 Series Bridge The PTP 600 Series Bridge PIDU Plus is used to generate the ODU supply voltage from the mains supply and

Page 174

31The Recovery switch is used to recover the unit from configuration errors or software image corruption. To put a PTP 600 Series Bridge into Recove

Page 175 - 13.3 Software/Features

323.3.3 Redundancy and Alternate Powering Configurations NOTE: The use of DC supplies of less than 55v will reduce the usable distance between the

Page 176

333.3.3.2 External DC Supply and AC Supply To give redundancy through the use of mains and DC supply. Figure 9 - External DC Supply and AC Supply

Page 177

343.3.4 Remote LEDs and Recovery Switch The PTP 600 Series Bridge PIDU Plus provides a facility to connect remote LEDs and Recovery switch allowing

Page 178

35The PIDU Plus to ODU and the PIDU Plus to Network Equipment cables may be unscreened (UTP) or screened (STP). However, unscreened cables reduce th

Page 179

363.3.8 Configuration and Management Configuration and Management of the PTP 600 Series Bridge is implemented using an inbuilt web server hosting

Page 180

374 Product Architecture The PTP 600 Series Bridge consists of an identical pair of units deployed one at each end of the link. The radio link opera

Page 181 - 13.6 Regulatory Issues

2The system has basically been shown to comply with the limits for emitted spurious radiation for a Class B digital device1, pursuant to Part 15 of

Page 182

38 Figure 12 – PTP 600 Series Bridge Layer Diagram The PTP 600 Series Bridge functionality has been extended to encompass the specification IEEE 80

Page 183

395 General Considerations 5.1 Spectrum Planning The PTP 600 Series Bridge has two frequency variants in its product range. Band Definition F

Page 184

405.2 Region Codes The PTP 600 Series Bridge uses a system of Region Codes to control the operation of the radio link. The Region Code is set by a L

Page 185 - 13.8 Installation

41Region Code Frequency Band Regulations / Countries Max Tx Power EIRP Limit Operational Restrictions (see section 5.3) 12 5.4 GHz ETSI, USA 7dBm

Page 186

42The radar detection algorithm will always scan the active channel for 60 seconds for radar interference before using the channel. This compulsory

Page 187

435.4 5.4GHz Specific Frequency Planning Considerations Adjustment of the lower center frequency allows the operator to slide the available frequen

Page 188

445.4.3 5.8GHz Specific Frequency Planning Considerations Adjustment of the lower center frequency allows the operator to slide the available frequ

Page 189

45The power reduction in the edge channels is presented in Figure 16. Figure 16 - 5.8 GHz Band Edge TX Power Reduction (Region Code 1 Only) 5.5 Dis

Page 190

465.6 Networking Information The PTP 600 Series Bridge operates as a transparent Ethernet bridge. Each unit requires an IP address. This IP addres

Page 191

476 Site Planning 6.1 Site Selection Criteria The following are guidelines for selecting the installation location of the ODU and PDU Plus for a

Page 192

3Regulations applicable to 5.4GHz PTP 600 Series Bridge variant Examples of Regulatory Limits at 5.4GHz Non-FCC and Non-ETSI2Equipment can be oper

Page 193 - 14 E1/T1 Installation Guide

486.1.3 Path Loss Considerations The path loss is the amount of attenuation the radio signal undergoes between the two ends of the link. The path

Page 194

496.1.4 Aggregate Ethernet throughput rate v maximum link loss The equipment capability is given in Table 7 and Table 8. These tables give the Ethe

Page 195

50Modulation Mode / Payload Type Maximum Aggregate Data Rate10 11(Mbit/s) Threshold Value (dBm) Output Power (dBm) Maximum Link Loss (dB) 256QAM 0.8

Page 196

517 Installation Motorola recommends that only qualified personnel undertake the installation of a PTP 600 Series Bridge solution. 7.1 Preparation

Page 197

527.4 Installation Support Online installation support and contact details for your regional support can be found at http://www.motorola.com/ptp A

Page 198 - 14.3 Routing the Cable

53Pole diameters of 25mm (1”) to 50mm (2”) can be accommodated by inverting the back of the bracket as shown in Figure 17. Figure 17 - Mounting to

Page 199

54The length of the safety lanyard must not exceed 1m (approx 3 ft) in length. The lanyard should be made from a material that does not degrade in a

Page 200 - 14.6 Lightning Protection

55 Figure 19 - Completed ODU connector Both ends of the ODU cable are terminated in the same way. The above procedure should be repeated for the PID

Page 201

567.7.2 Making the Connections at the ODU Looking at the back of the unit with the cable entry at the bottom, the PTP 600 Series Bridge PIDU Plus c

Page 202

577.7.3 Making the PTP 600 Series Bridge PIDU Plus Connection At The ODU The following procedure describes how connection is made at the ODU. It is

Page 203 - 14.7 Surge Arrestor Wiring

4Regulations applicable to 5.8GHz PTP 600 Series Bridge variant Examples of Regulatory Limits USA/ Canada/ Taiwan/ Brazil Equipment can be opera

Page 204

58Should it be necessary to disconnect the PIDU Plus to ODU cable at the ODU, this can be achieved by removing the weather proofing gland and depres

Page 205

597.7.6 Grounding the Installation The Outdoor Unit (ODU) must be properly grounded to protect against power surges. It is the user’s responsibili

Page 206

60 Step 3: Replace the cover and secure with the retaining screw 7.7.8 Making the Network Connection at The PIDU Plus – PTP 600 Series Bridge The

Page 207 - 15 Data Rate Calculations

617.7.9 Mounting the PTP 600 Series Bridge PIDU Plus This step is optional. Motorola recommends that you mount the PIDU Plus on a wall or other sui

Page 208

62WARNING: The PIDU Plus is not waterproof and should be mounted away from sources of moisture. If mounted outdoors, the unit should be mounted in a

Page 209

63WARNING: It is possible for moisture to enter the cable due to damage to the outer protective layer. This moisture can track down the inside of th

Page 210

647.7.11 Aligning the PTP 600 Series Bridge ODUs The following is a description of the steps taken to establish a radio link between the two unit

Page 211

65 The following behavior should be noted: • When first started up and from time to time, the

Page 212 - 16 AES Encryption Upgrade

66 8 Web Page Reference The web user interface has three main sections. The home page presents

Page 213

67The navigation bar on the left hand side of the web page is used to move between the various management pages. The currently selected page is alwa

Page 214

5General Notice Applicable to Europe This equipment complies with the essential requirements for the EUR&E Directive 1999/5/EC. The use of 5.8GH

Page 215

688.1 Home Page – PTP 600 Series Bridge The home page for the PTP 600 Series Bridge has been designed to display a high level summary of the status

Page 216

698.1.1 Home Page Alarm Display The home page is also used to display all outstanding major system alarms. Whenever system alarms are asserted, a y

Page 217

70Install Status: If any errors are detected during the installation process, the unit will automatically raise an audible alarm. The install statu

Page 218

71Telecoms Channel A Status: Indicates that there is a problem with the telecoms channel A. Possible problems are "No Signal (local)", &q

Page 219

728.2 Systems Status Page The status page has been designed to give the system administrator a detailed view of the operation of the 600 Series Br

Page 220

73The following section details all the attributes displayed on the status page: Link Name: The link name is allocated by the system administrator a

Page 221

74 Ethernet Speed and Duplex: The negotiated speed and duplex setting of the Ethernet interface.

Page 222

75Vector Error: The vector error measurement compares the received signal’s In phase / Quadrature (IQ) modulation characteristics to an ideal signal

Page 223 - 17.5 Legal Notices

76Transmit Data Rate: The data rate in the transmit direction, expressed in Mbps and presented as: max, mean, min, and latest histogram format. The

Page 224

77Range: The range16 between the 600 Series bridge ODUs. Refresh Page Period: The Status page refreshes automatically according to the setting ente

Page 225

6 1 About This User Guide ...19 1.1 Interpreti

Page 226

78The features that are only available to the system administrator are: • Configuration • Statistics • The Installation Wizard • Software Upgrade •

Page 227

79The general configuration allows modification of high level administrative (descriptive) attributes and high level wireless configuration. The LAN

Page 228 - 18 Glossary

80 While the majority of the system configuration is entered during installation and should neve

Page 229 - 19 FAQs

818.3.1.2 LAN Configuration Page The LAN configuration page (Figure 31) is used by the system administrator to configure the 600 Series bridge’s LA

Page 230

82IP Address: Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify this unit on a network.

Page 231

83Local Packet Filtering: When Local Packet Filtering is Enabled, the bridge learns the source MAC addresses of devices transmitting Ethernet pack

Page 232 - 20 Index

84 This will be followed by a pop-up dialogue box asking to confirm the action. Note: At this point you will lose connection to the unit. If you hav

Page 233 - 21 Specifications

85 Figure 34 - VLAN Configuration Fields

Page 234

86VLAN Management VID: This 802.1Q VLAN VID will be included in packets generated by the management interfaces. Valid settings are in the range 0 to

Page 235

87Force Configuration: This option allows the user to force the speed and duplex setting of the Ethernet interface. Warning: Over the air throughput

Page 236

75.4 5.4GHz Specific Frequency Planning Considerations ...43 5.4.1 Raster Considerations...

Page 237

88 Figure 37 - Save Configuration File Screen

Page 238

89The configuration file is encoded using an ASCII encoding scheme. An example is show in Figure 38. Figure 38 – PTP 600 Example Configuration Fil

Page 239

90The restoration of configuration files can be performed using the Restore configuration tool. Using the browser button to locate the configuration

Page 240

91 Figure 40 - Reset Configuration and Reboot Confirmation Pop-up On confirmation the PTP 600 Series Bridge will: • Upload the configuration file •

Page 241 - 21.2 Safety Compliance

928.3.1.6 Telecoms Configuration Page The Telecoms page is only available when the Telecoms Interface has been set to either T1 or E1 in the Instal

Page 242

93Telecoms Interface: May be either T1, E1 reflecting the Installation Wizard setting. Line Code: Displays the Line Code setting for each channel. T

Page 243

948.3.2 Statistics Page The 600 Series bridge statistics page is designed to display some key statistics of the Ethernet Bridge and the underlying

Page 244 - 21.5 Radio Certifications

95 Wireless Tx Packets: This displays the total number of good packets the bridge has sent for t

Page 245 - 21.7 System Connections

96Transmit Modulation Mode: The modulation mode currently being used on the transmit channel. The number in brackets after the modulation mode and c

Page 246

978.3.3 Detailed Counters Page Figure 43 - Detailed Counters Page

Commentaires sur ces manuels

Pas de commentaire