Motorola bmc9022 Manuel d'utilisateur télécharger pdf

off and turns back on. Continue hold-

ing the [DEVICE] key and press the

numberkeys, one at a time, starting

with 1, then2, 3...0. Stop pressing the

number keys when the device turns

off.

STEP3 Release the [DEVICE] key to

save the code. The Device

LED will blink twice to confirm

the code is stored.

Repeat the steps above for all components

(CBL, TV, DVD).

Manual Pr

ogramming

The remote control can be programmed

by entering a three-digit code number

that corresponds to particular brands

and models of equipment. The three-

digit code numbers are listed in the

code tables sections of this instruction

manual.

STEP1 Turn on the equipment that you

want the remote control to

operate (Cable Box, TV or DVD) .

STEP2 Press the [DEVICE] button and

the [OK/SEL] button simultane-

ously for three seconds. The

corresponding device LED will

turn on indicating that it is ready

to be programmed. The LED will

remain on for 30 seconds. The

next step must be entered while

the LED is on.

STEP3 Point the remote control

toward the equipment and

enter the three-digit code

number assigned to your

brand from the code tables.

If there are more than one

three-digit number listed for

your brand, try one code

number at a time until your

equipment turns off.

*Note: You can verify that you have

selected the correct code by

pressing the [POWER] button.

The equipment should turn

back on. Then try all of the

functions on the remote control

(i.e. volume, mute, etc.) to

ensure you have the correct

code. If any of the functions do

not operate as they should,

repeat the instructions from

STEP 3 above using the next

three digit code number from

the brand list.

STEP4 Store the three-digit code by

pressing the same [DEVICE]

button once again. The device

LED will blink twice to confirm

that the code has been stored.

Auto Sear

ch Method

If none of the three digit code numbers

assigned to your brand of equipment works,

or the code table does not list your brand,

you can use the Auto Search Method to

find the correct three-digit code number for

your equipment by following steps:

STEP1 Turn on the equipment that you

want the remote control to

operate (Cable Box, TV or DVD).

STEP2 Press the [DEVICE] button and

the [OK/SEL] button simulta-

neously for three seconds.

The device LED will turn on

indicating that it is ready to be

programmed. The LED will

remain on for 30 seconds. The

next step must be entered

while the LED is on.

STEP3

Press the [CH] or [CH] button

one at a time or keep it

pressed. The remote will emit

a series of Power ON/OFF

code signals. Release the

[CH] or [CH] button as soon

as the equipment turns off.

*Note: You can verify that you have

selected the correct code by

pressing the [POWER] button.

STEP2 Press the [TV] button.

STEP3 Point the remote control

toward the TV and enter the

three-digit code for your TV

from the TV codes table.

STEP4 Store the three-digit code by

pressing the [DVD] button.

The device LED will blink

twice to confirm that the

code has been stored.

The Lear

ning Method

STEP1 Press the [Device] button

(CBL, TV or DVD) to be

programmed and the [INPUT]

buttons simultaneously for 3

seconds until the Device LED

light turns on.

STEP2 Line up the UR3L-SR4 to the

other remote, head-to-head,

1 or 2 inches apart.

STEP3 Press any button on the UR3L-

SR4 that you want to teach a

command to. For example, if

you want to teach the [MUTE]

button, press the [MUTE] button.

STEP4 Press and hold the [MUTE]

button on the other remote

until the UR3L-SR4 Device LED

light blinks twice.

*Note : The LED will blink 5 times if there

was an error in the learning

process. In so, repeat STEPS 3 and

4. Continue learning other buttons

by repeating STEPS 3 and 4.

STEP5 Once you have completed

teaching UR3L-SR4 all desired

commands for that Device,

save the learned commands

by pressing the [Device] and

[INPUT] buttons simultane-

ously until the Device LED

blinks 3 times. Now test all the

buttons to make sure they

learned correctly.

Erasing a Single Lear

ned

Command

STEP1 Press the [Device] and [INPUT]

buttons simultaneously for 3

seconds until the Device LED

light turns on.

STEP2 Press and hold the button you

want to erase for 3 seconds.

The Device LED will blink

twice to confirm the erasure.

STEP3 To exit, press and hold both the

[Device] and [INPUT] buttons

simultaneously until the Device

LED blinks 3 times.

Erasing All Lear

ned Commands

om One Device

STEP1 Press the [DEVICE] and

[INPUT] buttons simultane-

ously for 3 seconds until the

Device LED light turns on.

STEP2 Press and hold both the

[DEVICE] button you want to

erase and the [PAUSE] button

for 5 seconds. The Device LED

will blink twice to confirm the

erasure.

STEP3 To exit, press and hold both the

[DEVICE] and [INPUT] buttons

simultaneously until the Device

LED blinks 3 times.

I. Pr

ogramming the All Of

f Button

This allows you to program the All Off

button so it can send up to three power

On/Off commands with one button press.

STEP1 Press the [CBL] button.

STEP2 Press the [All OFF] button and the

[OK/SEL] button simultaneously

for 3 seconds. The [CBL] button

will turn on for 30 seconds.

STEP3 Press the first [Device] button

you want to store in the [ALL OFF]

button and then the [POWER]

button. Repeat this for other

Device until you have stored all

the desired power commands

into the [ALL OFF] button.

STEP4 Press the [CH] button to save

the power commands you

stored. The [CBL] button will

blink twice to confirm the

Device have been saved.

ogramming for

Advanced Functions.

If your remote model has custom-

programmable Macro buttons available,

they can be programmed to act as a

‘Macro’ or Favorite Channel button in

CABLE mode. This allows you to program

up to five 2-digit channels, four 3-digit

channels or three 4-digit channels that

can be accessed With one button press.

*Note : The FAV button is not

programmable if you have a

Digital Cable Box made by

Pace, Pioneer or CISCO/SA.

STEP1 Press the [CBL] button to

select the CBL mode.

STEP2 Press the [MACRO] button and

[OK/SEL] button simultaneously

for 3 seconds. The [CBL] button

will turn on for 30 seconds.

STEP3 Enter the the 2, 3 or 4-digit

code for the channel you want

programmed first (for example,

007) using the Number Pad,

then press the [STOP] button.

Then enter the code for the

next channel (for example,

050), then press the [STOP]

button. Repeat this process for

the third channel. The [CBL]

button will blink once for each

channel entered.

STEP4 Press the [CH



] button to

store the channels that were

selected. The [CBL] button

will blink twice to confirm

the storage of commands.

To access the programmed channels,

press the [MACRO] button once. This

will bring up the first channel. Press

once again and it will bring up the

second channel. Press again and it

will bring up the third channel.

To erase the Macro programming

and return to the original function:

STEP1 Press the [CBL] button to

select the CABLE mode.

STEP2 Press a [MACRO] button and the

[OK/SEL] button simultaneously

for 3 seconds. The CBL device

LED will turn on for 30 seconds.

The next step must be performed

while the LED is on.

STEP3 Press the [CH



] button to

erase the functions stored in

the button. The CBL device

LED will blink twice to confirm

that the memory button has

been erased.

K. Pr

ogramming V

olume Contr

Volume and Mute control are factory-

programmed to automatically transfer

to the respective Device mode you

select, as follows:

CBL : TV TV : TV DVD : TV

If you wish to store the Cable volume

control in CBL mode, use the following steps.

STEP1 Press the [OK/SEL] button and

[CBL] button simultaneously for

three seconds. The device LED

will turn on for 30 seconds. The

next step must be performed

while the LED is on.

STEP2 Press the [VOL



] button.

The device LED will blink.

STEP3 Press [CBL] button. The

device LED will blink twice

to confirm the programming.

The equipment should turn

back on. Then try all of the

functions on the remote control

(i.e. volume, mute, etc.) to

ensure you have the correct

code. If any of the functions do

not operate as they should,

repeat the instructions from

STEP 3 above to continue the

Auto Search Method.

STEP4 Press the same [DEVICE]

button to store the code. The

Device LED will blink twice

to confirm that the code has

been stored.

o find the Thr

ee-Digit Code

that W

as Pr

ogrammed using

the Auto Sear

ch Method

STEP1 Press the appropriate [DEVICE]

button and the [OK/SEL] button

simultaneously for three seconds.

The device LED will turn on for

30 seconds. The next step

must be performed while the

LED is on.

STEP2 Press the [INFO] button. The

device LED will blink a number

of times indicating the number

of each digit for the code. Each

digit is separated by a one second

interval of the LED being off.

Example : One blink, then three blinks,

then eight blinks indicates

the code number 138.

*Note : Ten blinks indicates the number 0.

ogramming a Second

TV to the DVD Button

STEP1 Press the [DVD] button and

the [OK/SEL] button simultane-

ously for 3 seconds. The DVD

LED will turn on for 30 seconds.

The next step must be performed

while the LED is on.

Button Functions

Programming the Remote Control

Universal Remote Control, Inc.

www.universalremote.com

OCE-0082B REV 09 (02/14/12)

UR3L-SR4

Operating Manual

For Easy Clicker

This remote control is designed

to operate most IPTV and DTA

STBs as well as Digital and

Analog Cable Boxes.

Introduction

Replacing Batteries

Before you program or operate the

remote control, you must install

two new AAA alkaline batteries.

STEP1 Remove the battery com-

partment cover from the

back of your remote control.

STEP2 Check battery polarity

carefully, and install the

batteries as shown in the

illustration below.

STEP3

Replace the battery

compartment cover.

*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either the

CBL, TV, or DVD button, depending on which device you are programming the remote to operate.

A. Quick Set-Up Method

STEP1 Turn on the equipment you want toprogram. To program your TV, turn on the TV.

STEP2 Point the remote at the component andpress and hold the [DEVICE] key for 4seconds until the Device LED blinks

Note : To return CBL device to TV

volume repeat steps above

replacing [CBL] with [TV] in

Step 3.

ogramming Channel Contr

Channel controls are factory-programmed

to automatically transfer to the respective

Device mode you select, as follows:

CBL : CBL TV : CBL DVD : DVD

If you wish to store the TV channel

controls in TV mode, use the following

steps.

STEP1 Press the [OK/SEL] button and

[TV] button simultaneously for

three seconds. The device LED

will turn on for 30 seconds. The

next step must be performed

while the LED is on.

STEP2 Press the [VOL



] button. The

device LED will blink.

STEP3 Press [TV] button. The device

LED will blink twice to confirm

the programming.

Note : To return TV device to CBL

channel repeat steps above

replacing [TV] with [CBL]

in Step 3.

Low Batter

y W

ning

When the battery is low (2.3V-2.0V) and

needs to be replaced with fresh batteries,

device LED will blink 2 times in sequence

whenever a [DEVICE] button is pressed

to turn on equipment.

Memor

y Lock System.

This remote control is designed to

retain programmed memory for 10

years — even after batteries are

removed from the remote control.

For additional information about your

remote control, go to www

.universal-

remote.com

1 2

Résumé du contenu

Page 1 - For Easy Clicker

off and turns back on. Continue hold-ing the [DEVICE] key and press thenumberkeys, one at a time, startingwith 1, then2, 3...0. Stop pressing thenumbe

Page 2 - Set-up Code Tables

Manufacturer/BrandSet-Up Code NumberVCRManufacturer/BrandSet-Up Code NumberCABLE IPTVManufacturer/BrandSet-Up Code NumberTVManufacturer/BrandSet-Up Co

Commentaires sur ces manuels

Pas de commentaire

Motorola bmc9022 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Enregistreurs vidéo numériques (DVR) Motorola bmc9022. UR3L-SR4 Operating Manual For Easy Clicker Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Enregistreurs vidéo numériques (DVR) Motorola bmc9022