Motorola CPCI-6115 Manuel de service Page 105
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Functional Description Transition Module Preparation and Installation
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
103
Jumper J6 on the transition module controls the routing of the COM1 port to either the
processor board front panel or through the PIM 1 socket on the transition module. When pins
1 and 2 are jumpered on J6, the COM1 signal is routed to the PIM1 socket on the transition
module. When pins 2 and 3 are jumpered on J6 the COM1 signal is routed to the processor
board front panel. Jumper J11 on the transition module controls the routing of the COM2 port
to either the processor board front panel or through the PIM2 socket on the transition module.
When pins 1 and 2 are jumpered on J11, the COM2 signal is routed to PIM2 on the transition
module. When pins 2 and 3 are jumpered on J11, the COM2 signal is routed to the processor
board front panel.
5.7 Functional Description
The following subsections describe the major functional components of the CPCI-6115-
MCPTM transition module. There are certain differences between the IP version and the
CompactPCI model that are explained in the subsections where those differences apply.
5.7.1 IDE Flash
The CPCI-6115 SBC supports a single IDE channel routed to the J5 User I/O connector. The
CPCI-6115-MCPTM contains one 50-pin Type II connector which supports a removable IDE
CompactFlash memory card on the primary IDE channel. Refer to the CompactFlash Jumper
on page 102 for the definition of this connector. The CompactFlash connector is not accessible
through the rear panel. The CPCI-6115 transition module must be removed in order to install a
CompactFlash memory card.
Since the transition module receives its power from the host board through power pins on the
backplane, it cannot be removed in a hot-swap chassis without first removing the associated
host board, or by powering off the slot in some other way, via software or by toggling the lower
lever of the associated host board, so the blue LED illuminates. Since the CompactFlash is an
active component, and some PIMs are as well, damage to these active components may occur
if the transition module is not properly powered down.
Figure 5-4 COM1 and COM2 Serial Port Jumpers (J6/J11)
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(25 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.711 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels