Motorola CPCI-6115 Manuel de service Page 113
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing the PIM Transition Module Preparation and Installation
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
111
5.8 Installing the PIM
Procedure
If a PIM has already been installed on the CPCI-6115-MCPTM, or you are installing a transition
module as it has been shipped from the factory, disregard this section, and proceed to the main
installation section titled Installing the Transition Module on page 113. For PIM installation,
perform the following steps:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD strap to the
chassis as a ground. The ESD strap must be secured to your wrist and to ground
throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power off and remove
the AC cord or DC power lines from the system.
3. Remove chassis or system cover(s) as necessary for access to the CompactPCI.
4. Carefully remove the transition module from its CompactPCI card slot and lay it flat
on a stable surface.
5. Remove the PIM filler from the front panel of the transition module.
Product Damage
Inserting or removing modules in a non-hot-swap chassis with the power applied may
result in damage to the module components. The CPCI-6115-MCPTM is not a hot-
swap board, but it may be installed in a hot-swap chassis with power applied.
Remove the corresponding CPCI-6115 before the CPCI-6115-MCPTM is installed.
Personal Injury or Death
Dangerous voltages, capable of causing death, are present in this equipment.
Use extreme caution when handling, testing and adjusting.
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(25 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.406 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels