Motorola CPCI-6115 Manuel de service Page 32
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
Hardware Preparation and Installation Environmental, Power, and Thermal Requirements
30
Shipment Inspection
To inspect the shipment, perform the following steps:
1. Verify that you have received all items of your shipment.
2. Check for damage and report any damage or differences to customer service.
3. Remove the desiccant bag shipped together with the board and dispose of it
according to your country’s legislation.
2.3 Environmental, Power, and Thermal
Requirements
The next sections describe the environmental, power, and thermal requirements for the CPCI-
6115.
2.3.1 Environmental Requirements
The following table lists the currently available specifications for the environmental and
mechanical characteristics of the CPCI-6115. A complete functional description of the CPCI-
6115 baseboard appears in Chapter 4, Functional Description. Specifications for the optional
PCI mezzanines can be found in the documentation for those modules.
You must make sure that the board, when operated in your particular system configuration,
meets the environmental requirements specified below.
The product is thoroughly inspected before shipment. If any damage occurred during
transportation or any items are missing, contact customer service immediately.
Operating temperatures refer to the temperature of the air circulating around the board
and not to the component temperature.
Table 2-1 CPCI-6115 Specifications
Characteristics Specifications
PMC I/O Signal Impedance 42 to 75 ohms (nominal impedance)
Operating temperature 0°C to +55°C (32°F to 131°F) entry air with forced-air cooling
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(25 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels