Motorola CPCI-6115 Manuel de service Page 45
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing PMC Modules on the CPCI-6115 Hardware Preparation and Installation
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
43
When it is determined that there are no bent pins on the board connectors or backplane,
carefully slide the board into the backplane slots until the board ejector handles come in contact
with the system chassis. Do not force the board into the backplane slot. As the handles
engage, apply forward pressure while pushing the ejector handles toward each other. Pushing
the handles towards each other seats the board into the backplane.
In most cases, PMC modules ordered with the baseboard are installed on the CPCI-6115 at the
factory and the order is shipped as a single unit. The user-configured jumpers on the PMCs are
accessible with the modules installed.
If you need to install PMCs on the baseboard, refer to Installing PMC Modules on the CPCI-
6115 on page 43 for the installation procedure. The procedure assumes the CPCI-6115 has
already been installed in the chassis.
2.7.1 Installing PMC Modules on the CPCI-6115
One dual-wide, one single-wide or two single-wide PCI mezzanine (PMC) modules can be
mounted on the CPCI-6115 baseboard. Each PMC slot has four connectors that provide a PCI
interface to two PMC slots that provide a user I/O to the backplane. Refer to Power
Requirements on page 32 for the total current available to PMCs and transition module.
Procedure
To install a PMC module follow these steps.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the AMC or electronic components, make sure that you are working
in an ESD-safe environment.
Product Damage
Inserting or removing modules in a non-hot-swap chassis with power applied may
result in damage to module components. The CPCI-6115 is a hot-swappable board
and may be inserted in a hot-swap chassis, such as a CPX2000, CPX8000 or MXP3000
series chassis with power applied.
Check to make sure your chassis is hot swap compliant.
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(25 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.893 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels