Motorola CPCI-6115 Manuel de service Page 186
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CPCI-6200 Installation and Use (6806800J66C)
Safety Notes
186
EMC
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules, EN55022. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, can cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user is required to correct the interference at his own expense.
Use only shielded cables when connecting peripherals to assure that appropriate radio
frequency emissions compliance is maintained. Installed blades must have the face plates
installed and all vacant slots in the shelf must be covered.
For applications where this product is provided without a face plate, or where the face plate has
been removed, your system chassis/enclosure must provide the required electromagnetic
interference (EMI) shielding to maintain EMC compliance.
Board products are tested in a representative system to show compliance with the above
mentioned requirements. A proper installation in a compliant system maintains the required
performance.
As soon as you modify the product or change the default configuration you are responsible for
complying with all relevant regulatory standards.
Installation
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product make sure that your are working in an ESD-safe environment or
wear an ESD wrist strap or ESD shoes. Hold the product by its edges and do not touch any
components or circuits.
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(174 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.614 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels