Gigabit Ethernet/82543PMC ModuleOwner’s Manual214134 Revision ABApril 2005 Edition
xiList of TablesTable 2-1. Supported Mode Settings... 2-3Table 3-1. Bezel Co
xiiiAbout this ManualThis manual describes and explains how to install the Gigabit Ethernet 82543 PCI mezzanine card (PMC). This network interface car
xivOverview of ContentsThis manual is divided into the following chapters and appendices:Chapter 1, Preparation and Installation, provides a brief des
xvEmbedded Communications ComputingReader Comments DW1642900 S. Diablo WayTempe, Arizona 85282You can also submit comments to the following e-mail add
xvirepresents the Control key. Execute control characters by pressing the Ctrl key and the letter simultaneously, for example, Ctrl-d.Note: Contains i
xviiDC Direct currentDSP Digital signal processorEEPROM Electrically erasable programmable read-only memoryESD Electrostatic dischargeFCC Federal Comm
1-111Preparation and InstallationIntroductionThis chapter provides a brief description of the Gigabit Ethernet/82543 PMC Module and explains how to in
1-2 Gigabit Ethernet/82543 PMC Installation and UseGigabit Ethernet Technology1Figure 1-1. PMC/Gigabit Ethernet/82543Gigabit Ethernet TechnologyGigab
© Copyright 2005 Motorola Inc.All rights reserved.Printed in the United States of America.Motorola and the stylized M logo are trademarks of Motorola,
Gigabit Ethernet TechnologyGigabit Ethernet/82543 PMC Installation and Use 1-31High PerformanceIn workgroup environments, Gigabit Ethernet can handle
1-4 Gigabit Ethernet/82543 PMC Installation and UseSystem Enclosure1Managers can rely on familiar network analysis tools and procedures in 10/100/1000
Guidelines for UnpackingGigabit Ethernet/82543 PMC Installation and Use 1-51accommodate a slightly wider board assembly into each slot. For more infor
1-6 Gigabit Ethernet/82543 PMC Installation and UseEquipment Required1place the component flat on a grounded, static-free surface (and, in the case of
Before You Install or Remove a BoardGigabit Ethernet/82543 PMC Installation and Use 1-71place the component flat on a grounded, static-free surface (a
1-8 Gigabit Ethernet/82543 PMC Installation and UseBefore You Install or Remove a Board1Use Caution When Installing or Removing Boards When first inst
Before You Install or Remove a BoardGigabit Ethernet/82543 PMC Installation and Use 1-91If your system is using software that provides full hot swap c
1-10 Gigabit Ethernet/82543 PMC Installation and UseBefore You Install or Remove a Board1Figure 1-2. Injector/Ejector Lever TypesEach lever type has
Installation and RemovalGigabit Ethernet/82543 PMC Installation and Use 1-111Installation and RemovalThe following instructions tell how to install or
1-12 Gigabit Ethernet/82543 PMC Installation and UseInstallation and Removal1equipment attached to the rear transition board may occur.Therefore, only
Installation and RemovalGigabit Ethernet/82543 PMC Installation and Use 1-1315. Remove the screws from the stand-offs on the Gigabit Ethernet/82543 PM
1-14 Gigabit Ethernet/82543 PMC Installation and UseInstallation and Removal1!CautionInsert the board by gently holding the injector levers - do not e
Installation and RemovalGigabit Ethernet/82543 PMC Installation and Use 1-151Continue to gently push until the prealignment guide pegs engage with the
1-16 Gigabit Ethernet/82543 PMC Installation and UseInstallation and Removal1Figure 1-5. Connecting to the Network2. Observe the appropriate green sp
Installation and RemovalGigabit Ethernet/82543 PMC Installation and Use 1-171Note: Auto-negotiation for speed and duplex is the default behavior for m
1-18 Gigabit Ethernet/82543 PMC Installation and UseInstallation and Removal13. Carefully remove the host module from its card slot and place it on a
2-122Functional DescriptionIntroductionThis chapter describes the Gigabit Ethernet/82543 PMC Module on a feature and block diagram level. Figure 2-1 o
2-2 Gigabit Ethernet/82543 PMC Installation and UseFunctional Components2❏ Automatic polarity correction❏ IEEE 802.3u auto-negotiation with next-page
Functional ComponentsGigabit Ethernet/82543 PMC Installation and Use 2-32The controller interfaces to the PCI bus directly and supports the Media Inde
2-4 Gigabit Ethernet/82543 PMC Installation and UseFunctional Components2Note: Based on current errata to the Intel 82543GC Gigabit Ethernet Controlle
Safety SummaryThe following general safety precautions must be observed during all phases of operation, service, and repair of thisequipment. Failure
Interrupt Request LineGigabit Ethernet/82543 PMC Installation and Use 2-52Interrupt Request LineThe interrupt request (IRQ) line for the Gigabit Ether
3-1333Controls, Indicators andConnector Pin AssignmentsIntroductionThis chapter provides details of controls, indicators as well as connector pin assi
3-2 Gigabit Ethernet/82543 PMC Installation and UseBezel Connector and LEDs3Figure 3-1. Bezel Connector and LEDsTable 3-1. Bezel Connector and LEDs
J1 and J2 PCI Bus ConnectorsGigabit Ethernet/82543 PMC Installation and Use 3-33Note: Based on current errata to the Intel 82543GC Gigabit Ethernet Co
3-4 Gigabit Ethernet/82543 PMC Installation and UseJ1 and J2 PCI Bus Connectors3Table 3-2. J1 PCI Bus Connector Pin Assignments Pin Signal Signal Pin
J1 and J2 PCI Bus ConnectorsGigabit Ethernet/82543 PMC Installation and Use 3-5357 V(I/O) AD03 5859AD02AD016061 AD00 +5V 6263 GND REQ64* 64Table 3-3.
3-6 Gigabit Ethernet/82543 PMC Installation and UseJ1 and J2 PCI Bus Connectors343 C/BE1* GND 4445 AD14 AD13 4647 GND AD10 4849 AD08 +3.3V 5051 AD07 N
J3 PCI Bus ConnectorGigabit Ethernet/82543 PMC Installation and Use 3-73J3 PCI Bus ConnectorTable 3-5 on page 3-8 identifies the 32-bit J3 PCI bus con
3-8 Gigabit Ethernet/82543 PMC Installation and UseJ3 PCI Bus Connector3Note: An asterisk (*) in a signal name indicates that the signal is active low
CE Notice (European Community)This is a Class A product. In a domestic environment, this product may cause radiointerference, in which case the user m
RJ-45 Ethernet ConnectorGigabit Ethernet/82543 PMC Installation and Use 3-93RJ-45 Ethernet ConnectorThe RJ–45 Ethernet connector resides on the PMC’s
3-10 Gigabit Ethernet/82543 PMC Installation and UseCross-Over Cable Connector (10/100 Mb/s Only)3 Cross-Over Cable Connector (10/100 Mb/s Only)To con
Loopback Connector (10/100 Mb/s Only)Gigabit Ethernet/82543 PMC Installation and Use 3-113Loopback Connector (10/100 Mb/s Only)You can create a loopba
AA-1ATroubleshootingError ListThis appendix provides a hint list for detecting erroneous system configurations and any untoward or unusual behavior of
A-2 Gigabit Ethernet/82543 PMC Installation and UseATable 3-1. Troubleshooting an Installation Problem Probable Cause Corrective ActionA speed/status
Gigabit Ethernet/82543 PMC Installation and Use A-3AThe 100 Mb/s mode has been selected, but the 100 Mb/s LED is not lit.A CD signal could not be dete
BB-1BSpecificationsSpecificationsThis appendix provides general specifications including mechanical, environmental and electrical for the Gigabit Ethe
B-2 Gigabit Ethernet/82543 PMC Installation and UseBPower Requirements!CautionDamage of PMC ModuleThe PMC Standard VITA 32 - 2003, Revision 1.0a, spec
NoticeWhile reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omission
Gigabit Ethernet/82543 PMC Installation and Use B-3B❏ 5V Rail : 0.4mAmp maximumThe power requirement of the Gigabit Ethernet/82543 PMC Module, which i
B-4 Gigabit Ethernet/82543 PMC Installation and UseB!CautionBoard DamageDo not operate the product outside the specified environmental limits. High hu
Gigabit Ethernet/82543 PMC Installation and Use B-5BEMC ComplianceThe Gigabit Ethernet/82543 PMC Module is an add-on module meant to be used in conjun
CC-1CRelated DocumentsEmbedded Communications Computing DocumentsThe Motorola publications listed below are referenced in this manual. You can obtain
C-2 Gigabit Ethernet/82543 PMC Installation and UseCManufacturers’ DocumentsTable C-2 lists the manufacturers’ data sheets and other useful manuals. P
Gigabit Ethernet/82543 PMC Installation and Use C-3CIEEE Standard for Local Area Networks: Carrier Sense Multiple Access with Collision Detection (CSM
IN-1IndexSymbols+5V signal ...3-4Numerics10 BaseTx ...2-110 BaseTx cablin
IndexIN-2 Gigabit Ethernet/82543 PMC Installation and UseINDEXchecking connection of ...A-2, A-3Cabling ... 1-3,
viiContentsAbout this ManualAudience ...
Gigabit Ethernet/82543 PMC Installation and Use IN-3INDEXElectrically erasable programmableread-only memory (EEPROM) .2-2, ...
IndexIN-4 Gigabit Ethernet/82543 PMC Installation and UseINDEXJJ1 PCI bus connector ...3-3pin assignments for ...
Gigabit Ethernet/82543 PMC Installation and Use IN-5INDEXPhysical requirements ... B-1Pin assignmentsfor cross-over cable connector
IndexIN-6 Gigabit Ethernet/82543 PMC Installation and UseINDEXSlot cover ...B-1Slot, PMC ...
viiiCHAPTER 2 Functional DescriptionIntroduction .......
ixList of FiguresFigure 1-1. PMC/Gigabit Ethernet/82543 .................. 1-2Figure 1-2. Injector/E
Commentaires sur ces manuels