Motorola PTP 500 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Mise en réseau Motorola PTP 500. Motorola PTP 500 User manual [en] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 26
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
1
PTP 300/500 Series
Deployment Guide
Contents
Protect Your Installation.............................................................................................................................. 2
Checklist, Site Survey and Tools................................................................................................................. 5
Bench Testing (Optional)............................................................................................................................. 6
Mast, Tower or Building Installation ..........................................................................................................10
Installation Wiring......................................................................................................................................13
Cable Preparation and Installation............................................................................................................14
Testing and Fault Finding (Troubleshooting).............................................................................................17
Installation and Commissioning................................................................................................................. 20
User Information to be Recorded.............................................................................................................. 23
Registration Warranty and Ordering Information....................................................................................... 25
License Keys and Regulatory Information................................................................................................. 26
Vue de la page 0
1 2 3 4 5 6 ... 25 26

Résumé du contenu

Page 1 - PTP 300/500 Series

1 PTP 300/500 Series Deployment Guide Contents Protect Your Installation...

Page 2 - Attention

10 Mast, Tower or Building Installation Hoist and Safety Loop Use the integral safety loop for hoisting the ODU up a mast, tower or building. When t

Page 3 - Lightning Protection Zones

11 Mast, Tower or Building Installation Mast or Tower Installation Instructions The ODU is pre-fitted with a mounting bracket (designed to ease insta

Page 4

12 Mast, Tower or Building Installation Step 2: Offer the ODU (with pre-fitted mounting bracket) to the bracket strap and affix using the captive M8

Page 5 - Checklist

13 Installation Wiring More information: PTP 300 Series User Guide or PTP 500 Series User Guide Section: “Lightning Protection”

Page 6 - Bench Testing (Optional)

14 Cable Preparation and Installation The maximum cable length between the ODU and the user’s network equipment is 100 m (330 ft). CAUTION: Check

Page 7

15 Cable Preparation and Installation Cable and Gland Installation To install the cables and glands, follow these steps: Step 1: Make a cable as spe

Page 8 - Configuration Checks

16 Cable Preparation and Installation Step 4: When the gland body has been fitted, tighten the gland back shell. Caution! Do not over tighten th

Page 9 - Paired Unit

17 Testing and Fault Finding (Troubleshooting) Perform troubleshooting (fault finding) procedures either on a newly installed link, or on an operatio

Page 10 - Hoist and Safety Loop

18 Testing and Fault Finding (Troubleshooting) (*1) Power LED is Off Unplug the ODU connection from the PIDU and check the power LED illumination. I

Page 11

19 Testing and Fault Finding (Troubleshooting) Table 1 - Resistance Table Referenced to the RJ45 at the PIDU Resistances should fall within + or -10

Page 12 - PTP 300 Series User Guide

2 Protect Your Installation Attention ElectroMagnetic Discharge (Lightning) Protect Your Installation! EMD (Lightning) damage is not covered under w

Page 13 - Installation Wiring

20 Installation and Commissioning Aligning the PTP 300 or PTP 500 Series Bridge ODUs The PTP 300 and PTP 500 Series Bridges use audible tones durin

Page 14 - 36 mm min

21 Installation and Commissioning Behaviour During Installation The following behavior should be noted: • Band scan: When first started up and fro

Page 15 - Cable and Gland Installation

22 Installation and Commissioning Adjust Power Settings The transmit power levels of the installed units must be adjusted to ensure they are not too

Page 16 - Section: “Connecting Up”

23 User Information to be Recorded Use Table 2 and Table 3 to record the specified information. This information will be useful if there is a need t

Page 17

24 User Information to be Recorded User Notes

Page 18 - Table 1

25 Registration Warranty and Ordering Information The PTP 300/500 is an extraordinarily robust radio communications link with unsurpassed availabil

Page 19

26 License Keys and Regulatory Information Unit A1, Linhay Business Park Eastern Road, Ashburton Devon, TQ13 7UP, UK Telephone Support: +1 877 51

Page 20

3 Protect Your Installation Lightning Protection Zones When the ODU is installed on a mast, tower or wall, it may be in one of two possible lightni

Page 21 - DVM Alignment

4 Protect Your Installation Additional Grounding Requirements for Connectorized ODU Where the ODU is mounted outdoors and is mounted some distance

Page 22 - Items for Future Reference

5 Checklist, Site Survey and Tools CAUTION: Before performing an installation of a Motorola PTP 300 or PTP 500 Series system, ensure that you have re

Page 23 - Table 2 – Resistance Values

6 Bench Testing (Optional) It is advised that the link be configured and tested on a bench before the final installation of the units on a pole or a

Page 24 - User Notes

7 Bench Testing (Optional) NOTE: If the power LED does not illuminate, remove the power cable and the ODU connection from the PIDU Plus. Re-connect t

Page 25 - Item Part Number

8 Bench Testing (Optional) Configuration Checks Step 1: Use a web browser to connect to IP address http://169.254.1.1 for Slave and http://169.254.1

Page 26 - Doc Ref: phn1146_003v002

9 Bench Testing (Optional) Step 4: Access the ‘Installation Wizard’ page. Confirm the target MAC Address, Master/Slave choice, Symmetry, Max Transmi

Commentaires sur ces manuels

Pas de commentaire