Motorola PTP 500 Guide de l'utilisateur

PTP 500 Series User Guide MOTOROLA POINT-TO-POINT WIRELESS SOLUTIONS

Contents viii15.1.6 Right to Use Motorola’s Name ... 208 15.1

7 Web Page Reference 80Half Duplex data transmission means that data can be transmitted in both directions on a signal carrier, but not at the sa

7 Web Page Reference 81Vector Error The vector error measurement compares the received signal’s In phase / Quadrature (IQ) modulation characteris

7 Web Page Reference 82Receive Modulation Mode The modulation mode currently being used on the receive channel. A list of all the modulation mode

7 Web Page Reference 837.4 System Administration Figure 39 shows the system administration login page. By default a system administrator passwo

7 Web Page Reference 847.5 Configuration The configuration of the PTP 500 Series Bridge is organized into the following sections: • System Confi

7 Web Page Reference 85 While the majority of the system configuration is entered during installation and should never require changing, this pag

7 Web Page Reference 86 7.5.2 LAN Configuration The LAN configuration page (Figure 41) is used by the system administrator to configure the PTP

7 Web Page Reference 87Gateway IP Address The IP address of a computer / router on the current network that acts as a gateway. Use VLAN For Manag

7 Web Page Reference 88Figure 42 - Configuration Reboot Page Figure 43 - Configuration Reboot Page - Ethernet Auto Negotiation Disabled This w

7 Web Page Reference 89 Figure 44 - VLAN Configuration Fields When VLAN is enabled, the LAN Configuration page contains the following extra fie

Contents ix16.3.6 PTP 58500 Available Spectrum Settings... 246 16.3.7 PTP 58

7 Web Page Reference 907.5.2.3 LAN Configuration Page for Manual Ethernet Configuration The layout of the LAN Configuration page changes if Ethe

7 Web Page Reference 91 7.5.3 QoS Configuration Page The QoS configuration page (Figure 46) allows the system administrator to configure the cla

7 Web Page Reference 92In the case where the ODU is upgraded from an earlier release that does not support the 'Multiple Traffic Classes&apo

7 Web Page Reference 937.5.4 Save and Restore The save and restore feature of a PTP 500 Series Bridge allows the system administrator to backup

7 Web Page Reference 94Figure 48 - Save Configuration File Screen The configuration file is encoded using an ASCII encoding scheme. An example

7 Web Page Reference 95CAUTION The configuration file is currently restricted to a single software version and can only be restored into a wirele

7 Web Page Reference 96 Figure 51 - Reset Configuration and Reboot Confirmation Pop-up On confirmation the PTP 500 Series Bridge will: • Uploa

7 Web Page Reference 977.5.5 Telecoms Configuration The Telecoms page (Figure 52) is available when the Telecoms Interface has been set to eithe

7 Web Page Reference 98A "Wireless" loopback sends the telecoms data received across the wireless link back across the link on the same

7 Web Page Reference 997.6 Statistics The System Statistics page (Figure 53) displays some key statistics of the Ethernet Bridge and the underl

List of Figures xList of Figures Figure 1 - Typical PTP 500 Series Bridge Deployment...

7 Web Page Reference 100Ethernet Tx Packets This displays the total number of good packets the bridge has sent for transmission by the local Ethe

7 Web Page Reference 101Receive Modulation Mode The modulation mode currently being used on the receive channel. The number in brackets after the

7 Web Page Reference 1027.6.1 Detailed Counters The Detailed Counters page (Figure 54) displays detailed statistics of the Ethernet Bridge and t

7 Web Page Reference 103 The Detailed Counters page is subdivided into two columns. Column one presents the detailed statistics for the bridge’s

7 Web Page Reference 104Tx FIFO Drops Total number frames dropped due to lack of capacity in the transmit buffer, for example when the PTP 500 Se

7 Web Page Reference 105 Table 12 – PTP 500 Series Bridge Factory Configuration Values Example PTP 500 Series Configuration Data For your conveni

7 Web Page Reference 106 7.7.2 Manual Configuration If the installer / system administrator wishes, they may modify the default installation con

7 Web Page Reference 107If a valid license key is not detected in the unit’s non-volatile memory then the user is prompted to enter a valid key.

7 Web Page Reference 108Use VLAN Management Interface Controls whether the management interfaces (HTTP/SNMP/SMTP/SNTP) use a VLAN. Selecting this

7 Web Page Reference 109 7.7.3.1 Telecoms Interface If the Telecoms Interface field is set to either T1 or E1, then Step 1 of the installation wi

List of Figures xiFigure 27 - Connecting the PIDU Plus to the ODU... 5

7 Web Page Reference 110Lowest Telecoms Modulation Mode The lowest modulation mode at which telecoms data will be sent, if there is sufficient li

7 Web Page Reference 111 7.7.4 Installation Wizard Step 2 - Wireless Configuration Step 2 of the installation wizard requires the installer to e

7 Web Page Reference 112The Wireless Configuration page contains the following fields: Target MAC Address This is the MAC Address of the peer uni

7 Web Page Reference 113Link Symmetry is subject to the following restrictions: "Adaptive" is not supported in regions where radar avoi

7 Web Page Reference 114NOTE A raster limits the selection of the Rx frequency based upon the setting of the Tx frequency. Installation Tones W

7 Web Page Reference 115 7.7.5 Installation Wizard Step 3 - Confirm Configuration Step 3 of the installation wizard requires the installer to co

7 Web Page Reference 116Figure 62 - Reboot Confirmation Pop Up All the attributes are committed to non-volatile memory. Immediately following th

7 Web Page Reference 117 7.7.6 Disarm Installation Figure 63 is an example of the Disarm Installation screen. The screen contents vary depending

7 Web Page Reference 118 When Section 7.7.5 “Installation Wizard Step 3 - Confirm Configuration” is complete, the installation is armed and reboo

7 Web Page Reference 119 7.7.7 Graphical Install To aid the installation of wireless links two graphical installation aids have been introduced

List of Figures xiiFigure 54 - Detailed Counters Page ...

7 Web Page Reference 120The installation metric is simply the instantaneous receive power in dBm + 100. The PDA installation tool is accessed via

7 Web Page Reference 121The software upgrade pages are used to update a unit’s operational software. The software image to be uploaded should be

7 Web Page Reference 1227.8.2 Program Software Image into Memory The user should ensure that the correct image is shown before pressing the “Pro

7 Web Page Reference 123Figure 69 - Software Upgrade Complete Page 7.8.4 Reboot After Software Upgrade Reboot the unit by clicking the “Reboot

7 Web Page Reference 124 7.9 Spectrum Management Spectrum Management Selection is the PTP 500 Series Bridge feature that monitors the available

7 Web Page Reference 1257.9.3 Measurement Analysis Spectrum Management uses statistical analysis to process the received peak and mean measureme

7 Web Page Reference 1267.9.4 The Spectrum Management Master / Slave Relationship The Spectrum Management operates in a master / slave relations

7 Web Page Reference 127Figure 71 - Spectrum Management as seen from the Master

7 Web Page Reference 128Figure 72 - Spectrum Management as seen from the Slave

7 Web Page Reference 129 7.9.5 Spectrum Management Configuration The following section describes the user modifiable configuration accessible fr

List of Figures xiiiFigure 81 - Remote Management - Diagnostic Alarms ... 141

7 Web Page Reference 1307.9.6 Barring Channels Channels can only be barred / unbarred by the system administrator from the master Spectrum Manag

7 Web Page Reference 131The colored bar represents the following channel state: Table 13 - Spectrum Management change state key Green Active The

7 Web Page Reference 1327.9.8 Active Channel History The active channel history is a time series display of the channels used by the PTP 500 Ser

7 Web Page Reference 133 7.9.9 Viewing Historic Spectrum Management Metrics Spectrum Management allows the system administrator to view the resu

7 Web Page Reference 1347.9.10 Spectrum Management (Fixed Frequency) The PTP 500 Series Bridge software allows a user to optionally fix transmit

7 Web Page Reference 135The only controls available to the master are the Statistics Window and Interference Threshold attributes. They will have

7 Web Page Reference 136 7.9.11 Spectrum Management Control with Radar Avoidance When operating with Radar Avoidance enabled the following varia

7 Web Page Reference 137 Figure 78 - Spectrum Management Slave Screen With Operational Restrictions The colored bar represents the following cha

7 Web Page Reference 138Region Bar Region Bar This channel has been barred from use by the local region regulator 7.10 Remote Management The Re

7 Web Page Reference 139 7.10.1 Control Access to HTTP Interface The attribute HTTP Access Enabled allows a user to stop any access to a unit via

List of Figures xivFigure 108 - Connectorized PTP 500 Series Bridge Status Page... 171 Figure 1

7 Web Page Reference 140SNMP TRAPs supported: • Cold Start • Link Up • Link Down • DFS Channel Change • DFS Impulsive Interference Figure 80 –

7 Web Page Reference 1417.10.5 Diagnostics Alarms A number of diagnostics alarms have been added to allow SNMP agents to receive traps and emails

7 Web Page Reference 142SNMP Enabled Traps The SNMP Enabled Traps attribute controls which SNMP Traps the unit will send. SNMP Community String T

7 Web Page Reference 143SMTP Destination Email Address The email address to which the PTP 500 Series bridge will send the alert messages. 7.10.8

7 Web Page Reference 144Daylight Saving See Section 7.10.9 “Setting the clock” 7.11 Diagnostics Plotter For the PTP 500 Series, the storage of l

7 Web Page Reference 1457.11.1 Diagnostic Plotter Page New for the PTP 500 Series is the system administration diagnostic plotter facility see Fi

7 Web Page Reference 146The trace selection allows the user to control which traces are plotted. As with other management pages the page refresh

7 Web Page Reference 1477.12 Change Password This page (Figure 84) is used to change the password for the system administration (The factory de

7 Web Page Reference 148The user must enter the license key and click the ‘Validate License Key’ button to check that the key is valid and progra

7 Web Page Reference 149 7.14 Properties The web page properties screen allows the user to configure the web page interface (Figure 88). Figure

List of Tables xvList of Tables Table 1 - Contact Information ...

7 Web Page Reference 1507.15 Reboot The reboot page allows the system administrator to perform commanded reboots of the wireless unit. The rebo

8 Recovery Mode 1518 Recovery Mode This section provides instructions to allow users to recover a PTP 500 link. The Motorola PTP 500 point-to-p

8 Recovery Mode 152Clicking on the warning page image will take the user on to the Recovery Option Page (Figure 92). Figure 92 - Recovery Options

8 Recovery Mode 153Recovery Reason Indicates the reason the unit is operating in Recovery mode. Possible reasons are “Recovery button active” or

8 Recovery Mode 154After carefully checking that correct image has been downloaded the user should reboot the unit by pressing the “Reboot Wirele

8 Recovery Mode 1558.3 Reset IP & Ethernet Configuration To reset IP & Ethernet configuration back to factory defaults the user should p

8 Recovery Mode 156Figure 98 - Reboot Confirmation Pop Up The unit will now reboot. The unit should now start up in normal mode but with the IP

8 Recovery Mode 157On confirmation the following page will be displayed (Figure 100). The user should now reboot the unit by pressing the “Reboot

8 Recovery Mode 1588.5 Erase Security Parameters To erase the unit's security parameters, the user should press the ``Zeroise Critical Secu

8 Recovery Mode 159On confirmation the following page will be displayed (Figure 103). Figure 103 - Zeroise Security Parameters Successful Page

List of Tables xviTable 27 – PTP 500 EMC Immunity Compliance Specifications... 217 Table 28 –

8 Recovery Mode 1608.6 Reboot This option can be used to reboot the unit. The user will now be presented with a pop up box asking them to confir

9 Troubleshooting (Fault Finding) 1619 Troubleshooting (Fault Finding) This section provides instructions for troubleshooting (fault finding) a

9 Troubleshooting (Fault Finding) 162Figure 105 – Link End Hardware Test Flowchart Start Is the green power LED on solid? Is the power LED flas

9 Troubleshooting (Fault Finding) 163 9.1.1 Power LED is Off If the green Power LED does not light up at all, perform the following tests: 1. R

9 Troubleshooting (Fault Finding) 164 9.1.2 Power LED is Flashing If the green Power LED flashes, perform the following tests on the RJ45 cable

9 Troubleshooting (Fault Finding) 165Figure 106 - PTP LPU Test Points If either test fails, replace or repair the RJ45 cable. 9.1.4 No Ethernet

9 Troubleshooting (Fault Finding) 1669.1.6 Connection is not 100BaseT If the Ethernet connection to the network is only 10BaseT, when 100BaseT i

9 Troubleshooting (Fault Finding) 167 Table 16 - Resistance Table Referenced To The RJ45 at the PIDU Plus Resistances should fall within + or -10

9 Troubleshooting (Fault Finding) 168 9.2 Test Radio Link 9.2.1 No Activity If there is no communication over the radio link and the unit at th

9 Troubleshooting (Fault Finding) 169 9.2.2 Some Activity If there is some activity but the link is unreliable or does not achieve the data rate

List of Tables xvii

10 Connectorized PTP 500 Series Bridge 17010 Connectorized PTP 500 Series Bridge This section details the changes and additional features relevan

10 Connectorized PTP 500 Series Bridge 17110.1.2 Antenna The antenna choices for the Connectorized bridge are described in 10.6 “Antenna Choices”

10 Connectorized PTP 500 Series Bridge 17210.2.2 Configuration Pages The Configuration web page for the connectorized variant is shown in Figure

10 Connectorized PTP 500 Series Bridge 17310.2.3 Installation Pages The installer is prompted to enter the Antenna Gain and Cable Loss (Connector

10 Connectorized PTP 500 Series Bridge 174 Spectrum Management Control Is used to configure the PTP 500 Series Bridge Spectrum Management feature

10 Connectorized PTP 500 Series Bridge 175EIRP The Confirm Installation Page displays the EIRP (Effective Isotropic Radiated Power), which descri

10 Connectorized PTP 500 Series Bridge 17610.3 Deployment Considerations The majority of radio links can be successfully deployed with the PTP 5

10 Connectorized PTP 500 Series Bridge 177 10.5.1 Cable Losses (FCC Regions Only) The FCC approval for the product is based on tests with a cabl

10 Connectorized PTP 500 Series Bridge 17810.7 Installation The section covers the generic installation instructions for the Connectorized versi

10 Connectorized PTP 500 Series Bridge 17910.7.3 Miscellaneous supplies The following miscellaneous supplies will be required: • Cable ties, cab

MOTOROLA, Inc. Point-to-Point Wireless Bridges – PTP 500 Series Software Release PTP 500-03-xx System User Guide May 28th, 2009 Ref: PHN-1115-003

List of Equations xviiiList of Equations Equation 1 - Peak power density in the far field ...

10 Connectorized PTP 500 Series Bridge 18010.7.6 Alignment Process When aligning antennas deployed with a Connectorized PTP 500 Series bridge uni

10 Connectorized PTP 500 Series Bridge 1818. Connect the other antenna to the Connectorized PTP 500 Series bridge. 9. Disconnect the cable to t

10 Connectorized PTP 500 Series Bridge 18210.7.11 Antenna Connection Weatherproofing Where a cable connects to an antenna or unit from above, a

10 Connectorized PTP 500 Series Bridge 18310.8 Additional Lightning Protection The following guidelines should be applied in addition to those d

10 Connectorized PTP 500 Series Bridge 18410.8.2 ODU Mounted Indoors Where the ODU is mounted indoors, lightning arrestors should be deployed whe

11 E1/T1 Installation Guide 18511 E1/T1 Installation Guide This section describes the installation and configuration of the E1/T1 interface. The

11 E1/T1 Installation Guide 18611.2 Connecting the E1/T1 Cable to the PIDU Plus The E1/T1 cable and the Ethernet cable share the LAN port of the

11 E1/T1 Installation Guide 187 11.2.1 E1/T1 Splitter Output Pin Connections The E1/T1 splitter output pin connections are specified in Table 18.

11 E1/T1 Installation Guide 188 11.3 Testing the E1/T1 Installation Test the telecoms links by performing loopback connections as described i

12 Data Rate Calculations 18912 Data Rate Calculations This section provides instructions, tables and graphs to allow calculation of the data rat

1 About This User Guide 11 About This User Guide Congratulations on the purchase of the PTP 500 Series Bridge from Motorola. The PTP 500 Series

12 Data Rate Calculations 1902. The tables in Section 12.3 contain data rates for links of zero range. Use the curves in Section 12.4 to look up

12 Data Rate Calculations 191 12.3 Data Throughput Capacity Table 19, Table 20 and Table 21 show the data throughput rates (Mbits/s) that are ac

12 Data Rate Calculations 192 Table 19 – Data Throughput for PTP 500, Link Symmetry = Adaptive or 3:1 PTP 500 Full: 15 MHz 10 MHz 5 MHz Modul

12 Data Rate Calculations 193 Table 20 – Data Throughput for PTP 500, Link Symmetry = 1:1, Link Optimization = IP PTP 500 Full: 15 MHz 10 MHz

12 Data Rate Calculations 194 Table 21 – Data Throughput for PTP 500, Link Symmetry = 1:1, Link Optimization = TDM PTP 500 Full: 15 MHz 10 MHz

12 Data Rate Calculations 195Figure 120 – PTP 500 Range Adjustment for Data Rates, Curve A

12 Data Rate Calculations 196Figure 121 – PTP 500 Range Adjustment for Data Rates, Curve B

13 AES Encryption 19713 AES Encryption This section describes how to encrypt a PTP 500 link. The following topics are described in this section:

13 AES Encryption 198 13.3.1 License Keys The first step when configuring link encryption is to enter the new license keys in both PTP 500 Series

13 AES Encryption 199Motorola recommends the following process for entering new license keys and minimizing service outage: 1. Open two browsers

1 About This User Guide 21.2 Contact Information Table 1 - Contact Information Postal Address: Motorola, Inc. Unit A1, Linhay Business Park, Eas

13 AES Encryption 200Figure 123 – AES Configuration Data Entry Page To enter AES link encryption configuration, follow this procedure: 1. Open

13 AES Encryption 201Figure 124 - Configuration Reboot Screen 13.4 Wireless Link Encryption FAQ 13.4.1 Encryption data entry fields are not av

14 Remote Software Upgrade by TFTP 20214 Remote Software Upgrade by TFTP This section describes how to upgrade the PTP 500 software remotely usin

14 Remote Software Upgrade by TFTP 2032. Monitor the values of the following tFTP attributes: tFTPSoftwareUpgradeStatus: The current status of th

15 Legal Notices 20415 Legal Notices This section provides legal notices including software license agreements. CAUTION Intentional or unintenti

15 Legal Notices 20515.1.2 Grant of License Motorola, Inc. (“Motorola”) grants you (“Licensee” or “you”) a personal, nonexclusive, non-transferab

15 Legal Notices 2064. Portions of the Software and Documentation are protected by United States copyright laws, international treaty provisions

15 Legal Notices 20715.1.4 Title; Restrictions If you transfer possession of any copy of the Software and Documentation to another party outside

15 Legal Notices 208You have no obligation to preserve the confidentiality of any proprietary information that: (i) was in the public domain at t

15 Legal Notices 20915.1.9 Maintenance Except as provided above, Motorola is not responsible for maintenance or field service of the Software und

1 About This User Guide 3 1.3.2 Terminology Motorola PTP system documents employ specific imperative terminology as follows: • ‘Type’ means typ

15 Legal Notices 21015.1.12 U.S. Government If you are acquiring the Product on behalf of any unit or agency of the U.S. Government, the follow

15 Legal Notices 21115.1.16 Survival of Provisions The parties agree that where the context of any provision indicates an intent that it survive

15 Legal Notices 212BZIP2 License Terms “bzip2" and associated library "libbzip2", are copyright (C) 1996-2000 Julian R Seward. A

15 Legal Notices 21315.2 Hardware Warranty in U.S. Motorola U.S. offers a warranty covering a period of one year from the date of purchase by th

16 PTP 500 Reference Information 21416 PTP 500 Reference Information This section describes the reference information and regulatory notices that

16 PTP 500 Reference Information 215 Table 23 – PTP 500 Ethernet Bridging Specifications Ethernet Bridging Specification Protocol IEEE802.3

16 PTP 500 Reference Information 216 Table 25 – PTP 500 Power Supply Specifications Power Supply Separate power supply unit (included) Dimens

16 PTP 500 Reference Information 217 16.1.3 PTP 500 EMC Immunity Compliance Top-level Specification ETSI 301-489. Table 27 – PTP 500 EMC Immuni

16 PTP 500 Reference Information 218 16.1.4 PTP 500 Environmental Specifications Table 28 – PTP 500 Environmental Specifications Category Speci

16 PTP 500 Reference Information 219 16.2 PTP 54500 Reference Information This section contains reference information for the PTP 54500 frequen

1 About This User Guide 4 1.4 Getting Additional Help To get information or assistance as soon as possible for problems that you encounter, foll

16 PTP 500 Reference Information 220NOTE In regions other than EU/USA, specific local regulations may apply. It is the responsibility of the inst

16 PTP 500 Reference Information 22116.2.3 PTP 54500 Regulatory Compliance The PTP 54500 complies with the regulations that are in force in the U

16 PTP 500 Reference Information 22216.2.3.2 PTP 54500 European Union Notification The PTP 54500 product is a two-way radio transceiver suitable

16 PTP 500 Reference Information 223 16.2.4 PTP 54500 Radio System Specifications Table 31 contains radio system specifications for the PTP 54500

16 PTP 500 Reference Information 22416.2.5 PTP 54500 Emissions and Radio Certifications Table 32 lists the EMC emissions specifications under whi

16 PTP 500 Reference Information 225 16.2.6 PTP 54500 Available Spectrum Settings The available spectrum settings for the PTP 54500 are illustrat

16 PTP 500 Reference Information 226Figure 126 - PTP 54500 Available Spectrum Settings - 10 MHz Channel Bandwidth Figure 127 - PTP 54500 Avail

16 PTP 500 Reference Information 227 16.2.7 PTP 54500 System Threshold, Output Power and Link Loss PTP 54500 system threshold, output power and m

16 PTP 500 Reference Information 228 Table 35 - PTP 54500 System Threshold Figures - TDM Mode (15 MHz bandwidth) Modulation Mode System Thresho

16 PTP 500 Reference Information 229 Table 36 - PTP 54500 System Threshold Figures - IP Mode (10 MHz bandwidth) Modulation Mode System Threshold

1 About This User Guide 51.6 Warranty Motorola’s standard hardware warranty is for one (1) year from date of shipment from Motorola or a Motorol

16 PTP 500 Reference Information 230 Table 37 - PTP 54500 System Threshold Figures - TDM Mode (10 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 231 Table 38 - PTP 54500 System Threshold Figures - IP Mode (5 MHz bandwidth) Modulation Mode System Threshold (

16 PTP 500 Reference Information 232 Table 39 - PTP 54500 System Threshold Figures - TDM Mode (5 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 233 16.2.8 PTP 54500 FCC Antenna Restrictions In FCC regions, external antennas from the list in Table 40 can be

16 PTP 500 Reference Information 234Manufacturer Antenna Type Gain (dBi) Parabolic Dish Gabriel Gabriel 2-foot Standard QuickFire Parabolic, Q

16 PTP 500 Reference Information 235Manufacturer Antenna Type Gain (dBi) Parabolic Dish RadioWaves Radio Waves 4-foot Parabolic, SP4-2/5 (34.6

16 PTP 500 Reference Information 236 16.3 PTP 58500 Reference Information This section contains reference information that is specific to the PT

16 PTP 500 Reference Information 237General Notice Applicable to Europe This equipment complies with the essential requirements for the EU R&

16 PTP 500 Reference Information 238 16.3.2 PTP 58500 Licenses and Region Codes PTP 58500 units may be operated in any of the regions listed in T

16 PTP 500 Reference Information 239Region Code License / Regulation Frequencies DFS Channel Bandwidth Max Power Notes 20 Thailand 5725 - 5850

1 About This User Guide 6Cable measuring card: A cable measuring card must NEVER be used at the ODU end connected to power from the PIDU Plus. I

16 PTP 500 Reference Information 240 16.3.3 PTP 58500 Regulatory Compliance The PTP 58500 complies with the regulations that are in force in the

16 PTP 500 Reference Information 241This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

16 PTP 500 Reference Information 242The use of 5.8 GHz for Point to Point radio links is not harmonized across the EU and currently the product m

16 PTP 500 Reference Information 24316.3.3.3 UK Notification The PTP 58500 connectorized product has been notified for operation in the UK, and w

16 PTP 500 Reference Information 244 16.3.4 PTP 58500 Radio System Specifications Table 43 contains radio system specifications for the PTP 58500

16 PTP 500 Reference Information 24516.3.5 PTP 58500 Emissions and Radio Certifications Table 44 lists the EMC emissions specifications under whi

16 PTP 500 Reference Information 246 16.3.6 PTP 58500 Available Spectrum Settings The available spectrum settings for the PTP 58500 are illustrat

16 PTP 500 Reference Information 247Figure 129 – PTP 58500 Available Spectrum Settings – 10 MHz Channel Bandwidth Figure 130 – PTP 58500 Availab

16 PTP 500 Reference Information 248Table 46 – PTP 58500 FCC Max Transmit Power at the Edge Channels (FCC) Channel Frequency (MHz) Max Power (dBm

16 PTP 500 Reference Information 249 16.3.7 PTP 58500 System Threshold, Output Power and Link Loss PTP 58500 system threshold figures are given i

1 About This User Guide 7 1.8 RF Safety WARNING To protect from overexposure to RF energy, observe the safety guidelines in this section. 1.8.1

16 PTP 500 Reference Information 250 Table 48 - PTP 58500 System Threshold Figures - TDM Mode (15 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 251 Table 49 - PTP 58500 System Threshold Figures - IP Mode (10 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 252 Table 50 - PTP 58500 System Threshold Figures - TDM Mode (10 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 253 Table 51 - PTP 58500 System Threshold Figures - IP Mode (5 MHz bandwidth) Modulation Mode System Threshold (

16 PTP 500 Reference Information 254 Table 52 - PTP 58500 System Threshold Figures - TDM Mode (5 MHz bandwidth) Modulation Mode System Threshold

16 PTP 500 Reference Information 255 16.3.8 PTP 58500 FCC Antenna Restrictions In FCC regions, external antennas from the list in Table 53 can be

16 PTP 500 Reference Information 256Manufacturer Antenna Type Gain (dBi) Flat Plate Parabolic Dish Gabriel Gabriel 4-foot High Performance Quic

16 PTP 500 Reference Information 257Manufacturer Antenna Type Gain (dBi) Flat Plate Parabolic Dish RadioWaves Radio Waves 2-foot Parabolic, SP2

17 FAQs 25817 FAQs Can I source and use my own PoE adaptor with the PTP 500 Series bridge? No. The PTP 500 Series bridge uses a non-standard PoE

17 FAQs 259Is the PTP 500 Series bridge an 802.11a device? No, although similar, the PTP 500 Series bridge uses different encoding and radio trans

1 About This User Guide 81.8.3 Power Density Exposure Limit The applicable power density exposure limit from the documents referenced above is:

18 Glossary 26018 Glossary ARP Address Resolution Protocol NLOS non-Line-of-Sight ARQ Automatic Repeat reQuest ODU Outdoor Unit BPSK B

Index IIndex 5.4 GHz Information 219 5.8 GHz Information 236 Adaptive Modulation 37 AES Encryption 197 Alarm 75, 76 Alarms 74 Diagnostics 141 Al

Index IIEIRP 175 Emissions 5.4 GHz 224 5.8 GHz 245 Encryption 197 Environmental 218 Ethernet 87, 100 Activity 165 Configuration 90, 155 Frames 2

Index IIILightning Protection Unit (LPU) Fitting 58 Limits 11 Line Of Sight (LOS) 25 Link Budget Connectorized Variant 176 Link Loss 38 5.4 GHz

Index IVRecovery Switch Remote 20 Reference Information 214 Region Codes 30 5.4 GHz 220 5.8 GHz 238 Regulations 10 Connectorized Variant 176

Index VTools 48, 178 Tower Installation 46 Transmit Power 69 Transmit Power Reduction 247 Troubleshooting 161 Upgrade 120, 152, 153 User Inter

Index VI MOTOROLA, the stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. US

1 About This User Guide 9 1.8.4 Calculated Distances and Power Compliance Margins Table 3 shows calculated minimum separation distances d, recom

Contents iContents 1 About This User Guide...

1 About This User Guide 10 1.9 Compliance with Regulations 1.9.1 General Changes or modifications not expressly approved by Motorola could void

1 About This User Guide 111.9.3 Radio and Television Interference If this equipment does cause harmful interference to radio or television recep

2 Product Description 122 Product Description This section provides a high level description of the PTP 500 product. It describes in general term

2 Product Description 13 2.2 Typical Deployment The PTP 500 Series Bridge consists of an identical pair of units deployed one at each end of the

2 Product Description 142.3 Frequency Variants The PTP 500 Series Bridge has been developed to operate within license exempt frequency bands. Th

2 Product Description 15 2.6 Outdoor Unit (ODU) The ODU is a self-contained unit. It houses both radio and networking electronics. The ODU for t

2 Product Description 16 2.7 PIDU Plus PTP 300/500/600 Series The PIDU Plus PTP 300/500/600 Series (Figure 3) is used to generate the ODU suppl

2 Product Description 17 2.7.2 ODU, LAN and Recovery At the bottom of the PIDU Plus is an entry point for the PIDU Plus to ODU cable, the 100Bas

2 Product Description 182.7.5 Mains Connection The input supply range for the PIDU Plus is 90V-264V AC, 47-63Hz. Mains connection to the PIDU Pl

2 Product Description 19 Figure 6 - External DC Supply Only Figure 7 - External DC Supply and AC Supply Figure 8 - External DC Supply and Redun

Contents ii2.7.4 Remote Connectors and Jumpers ... 17 2.7.5 Main

2 Product Description 20 2.9 Remote LEDs and Recovery Switch The PIDU Plus provides a facility to connect remote LEDs and Recovery switch allowi

2 Product Description 21 The cable used to connect the PIDU Plus to the users Network Equipment can be any standard CAT5e Cable. The PIDU Plus to

2 Product Description 222.12 Mounting Brackets The ODU is supplied with a bracket for mounting it to a pole of 50mm (2”) to 75mm (3”) in diamet

3 Product Features 233 Product Features This section provides descriptions of the main features of PTP 500 product architecture. The following t

3 Product Features 243.2 Management Function The management function of the PTP 500 Series Bridge is logically equivalent to a separate protocol

3 Product Features 25 3.4 Channel Bandwidth and Link Symmetry Control The PTP 500 series provides configurable channel bandwidth in the radio li

3 Product Features 263.8 Link Mode Optimization Link Mode Optimization allows the PTP 500 link to be optimized according to the type of traffic

3 Product Features 27 3.9 Telecoms Circuits The PTP 500 link provides native support for one E1 link, or one T1 link. The link relays unstructur

3 Product Features 283.9.3 Further Reading Installation details are provided in Section 11 “E1/T1 Installation Guide”. The E1 or T1 circuit is c

4 Planning Considerations 294 Planning Considerations This section provides information to help the user to plan a PTP 500 link. Each frequen

Contents iii4.6.2 PIDU Plus Site Selection ...34 4.

4 Planning Considerations 30• Fixed Frequency: This method allows the installer to allocate fixed transmit and receive frequencies on the units.

4 Planning Considerations 31 4.3 Radar Avoidance and Bandwidth Operation Where regulatory restrictions apply to certain channels these channel

4 Planning Considerations 32 4.4 Variable Channel Bandwidth Operation Channel bandwidths of 5, 10 and 15 MHz are supported for the PTP 500 produ

4 Planning Considerations 334.5.3 PTP LINKPlanner Link planning enables a link of known quality to be installed. This involves the acquisition o

4 Planning Considerations 34 4.6 Site Selection Criteria The following are guidelines for selecting the installation location of the ODU and PI

4 Planning Considerations 35 Force (in pounds) = 0.0042 . A . v2 Where A is the surface area in square feet and v is the wind speed in miles per

4 Planning Considerations 364.7.3 Wind Speed Statistics Installers are recommended to contact the national meteorological office for the country

4 Planning Considerations 37 4.8 Path Loss Considerations Path loss is the amount of attenuation the radio signal undergoes between the two end

4 Planning Considerations 38For minimum error rates on TDM links, the maximum modulation mode should be limited to 64QAM 0.75. The values for (BP

5 Lightning Protection 395 Lightning Protection This section provides instructions for protecting PTP 500 installations against lightning strik

Contents iv6.5.10 Powering Up...

5 Lightning Protection 40Zones A and B are shown in Figure 12. Figure 12 - ODU mounted in Zones A & B

5 Lightning Protection 41It may be possible to extend Zone B by installing a finial above the ODU ( Figure 13). Figure 13 – Using a Finial to Ext

5 Lightning Protection 42 5.2 LPU Detailed Installation The Lightning protection Unit should be mounted at the building entry point and must be

5 Lightning Protection 43 5.3 LPU Kit The PTP-LPU Kit is supplied with a 600mm ODU to PTP-LPU cable pre-fitted with glands. Figure 15 shows all

5 Lightning Protection 44Figure 16 - Simplified Circuit Diagram

5 Lightning Protection 455.5 LPU Installation Diagram This section contains a diagram to show how the components of PTP 500 sites are installed

5 Lightning Protection 46 5.5.1 Typical Mast or Wall Installation Figure 17 shows a typical PTP 500 Series mast or wall installation using PTP-L

6 Installation 476 Installation This section provides instructions for installing a PTP 500 link. It is advised that the link be configured and te

6 Installation 486.1 Installation Support Online installation support and contact details for your regional support can be found at http://www.m

6 Installation 496.4 Mounting the ODUs 6.4.1 Mounting Bracket The ODU is pre-fitted with a mounting bracket (designed to ease installation) and

Contents v7.9 Spectrum Management... 124

6 Installation 506.4.2 ODU Mounting Procedure The ODU must be mounted using the following steps, ensuring that the cable entry is at the bottom:

6 Installation 51Figure 21 - ODU Mounted on Pole 3. Adjust the elevation and azimuth of the unit before tightening to the required torque settin

6 Installation 52 6.4.3 Hoist and Safety Loop Use the integral safety loop (Figure 22) for hoisting the ODU up a mast, tower or building. When th

6 Installation 536.5 Connecting Up 6.5.1 Preparing the PIDU Plus To ODU Cable The maximum cable length between the ODU and the user’s Network E

6 Installation 546.5.1.2 Cable Assembly The cable should be assembled as shown in Figure 23: Figure 23 - Correct Cable Preparation for the Recomme

6 Installation 55CAUTION Check that the crimp tool matches the RJ45 connector being used. Both ends of the ODU cable are terminated in the same wa

6 Installation 56 6.5.2 Making the Connections at the ODU Looking at the back of the unit with the cable entry at the bottom, the PIDU Plus conne

6 Installation 576.5.3 Making the PIDU Plus Connection At The ODU The procedure for connecting the PIDU Plus cable to the ODU is described in Fig

6 Installation 58Figure 28 - Disconnecting the ODU CAUTION To prevent damage to the ODU while making or breaking the connection, ensure that pow

6 Installation 596.5.6 Grounding the Installation The Outdoor Unit (ODU) must be properly grounded to protect against power surges. It is the us

Contents vi9 Troubleshooting (Fault Finding)...1

6 Installation 60 Figure 29 - Connecting the ODU to the PIDU Plus Step 1: Undo the retaining screw and hinge back the cover. Step 2: Plug in the O

6 Installation 61 6.5.8 Making the Network Connection at the PIDU Plus The Network connection is made by connecting the user’s Network Equipment

6 Installation 62Figure 31 - Mounting the PIDU Plus Step 1: Fix the PIDU Plus to the wall using the lugs provided. Step 2: Make connections as pe

6 Installation 63 CAUTION Do not dress the RJ45 cables too tightly, as this may make the connections unreliable. Figure 32 shoes the correct and

6 Installation 64Figure 33 – PIDU Plus Drip Loop Configuration CAUTION It is possible for moisture to enter the cable due to damage to the outer

6 Installation 656.5.10 Powering Up The PTP 500 Series Bridge is supplied as a pair of matched Master/Slave units. The Master unit can now be po

6 Installation 66 6.6 Establishing a Radio Link The following is a description of the steps taken to establish a radio link between the two unit

6 Installation 67In each of the states detailed above, the unit should be aligned to give the highest pitch tone. It should be noted that if, when

6 Installation 68 • Ranging: The PTP 500 Series does not require the user to enter the link range. The Master unit typically takes less than 60 s

6 Installation 69 6.6.4 Adjust Power Settings The transmit power levels of the installed units must be adjusted to ensure they are not too high.

Contents vii10.7.10 Antenna Cable Fixing... 181

6 Installation 706.6.5 Disarm on Completion When the alignment process is complete, the installer MUST REMEMBER TO DISARM BOTH UNITS in the link

7 Web Page Reference 717 Web Page Reference This section describes the PTP 500 web user interface and provides instructions for operators. Th

7 Web Page Reference 72Figure 35 - Menu Navigation Bar

7 Web Page Reference 73The web user interface menu has three main options. • Home: This presents to the operator a high level summary of the PT

7 Web Page Reference 74System Clock If SNTP (Simple Network Time Protocol) is enabled, or the clock has been set, then a system clock attribute i

7 Web Page Reference 757.2.2 System Alarms The following system alarms are defined: Ethernet Link Status Current status of the Ethernet link. I

7 Web Page Reference 76Install Status A non-OK value indicates that signaling was received with the wrong MAC address. Note that it is very unusu

7 Web Page Reference 77Incompatible Master and Slave A non-zero value indicates that the master and slave ends of the wireless link are different

7 Web Page Reference 787.3 System Status The status page (Figure 38) gives the system administrator a detailed view of the operation of the PTP

7 Web Page Reference 79The two PTP 500 Series bridges units are arranged in a master and slave relationship. The roles of the units in this rela