Motorola MVME2400 Series Manuel de service Page 5
- Page / 178
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Safety Summary
Safety Depends On You
The following general safety precautions must be observed during all phases of operation, service, and repair of this
equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety
standards of design, manufacture, and intended use of the equipment. Motorola, Inc. assumes no liability for the
customer’s failure to comply with these requirements.
The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the
user of the product, should follow these warnings and all other safety precautions necessary for the safe operation of
the equipment in your operating environment.
Ground the Instrument.
To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground. The
equipment is supplied with a three-conductor AC power cable. The power cable must be plugged into an approved
three-contact electrical outlet. The power jack and mating plug of the power cable meet International Electrotechnical
Commission (IEC) safety standards.
Do Not Operate in an Explosive Atmosphere.
Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in
such an environment constitutes a definite safety hazard.
Keep Away From Live Circuits.
Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other
qualified maintenance personnel may remove equipment covers for internal subassembly or component replacement
or any internal adjustment. Do not replace components with power cable connected. Under certain conditions,
dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and
discharge circuits before touching them.
Do Not Service or Adjust Alone.
Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is
present.
Use Caution When Exposing or Handling the CRT.
Breakage of the Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To
prevent CRT implosion, avoid rough handling or jarring of the equipment. Handling of the CRT should be done only
by qualified maintenance personnel using approved safety mask and gloves.
Do Not Substitute Parts or Modify Equipment.
Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized
modification of the equipment. Contact your local Motorola representative for service and repair to ensure that safety
features are maintained.
Dangerous Procedure Warnings.
Warnings, such as the example below, precede potentially dangerous procedures throughout this manual. Instructions
contained in the warnings must be followed. You should also employ all other safety precautions which you deem
necessary for the operation of the equipment in your operating environment.
!
WARNING
Dangerous voltages, capable of causing death, are present in this
equipment. Use extreme caution when handling, testing, and
adjusting.
- MVME2400-Series 1
- Single Board Computer 1
- Installation and Use 1
- Restricted Rights Legend 2
- Document Terminology 4
- Safety Summary 5
- Safety Depends On You 5
- Contents 9
- Glossary 12
- List of Figures 13
- List of Tables 15
- 1Preparing and Installing the 17
- MVME2400-Series Module 17
- MVME240x Module 18
- PMCspan Expansion Mezzanine 19
- PCI Mezzanine Cards (PMCs) 19
- VMEsystem Enclosure 20
- System Console Terminal 20
- 1 2 3 4 5 6 7 8 25
- ESD Precautions 29
- 2064 9708 31
- Primary PMCspan 32
- 2081 9708 33
- Secondary PMCspan 34
- 2065 9708 35
- INTERRUPT ACKNOWLEDGE 38
- DEBUG port on 38
- Installation Considerations 39
- 2Operating Instructions 41
- Switches 42
- MVME240x 43
- Status Indicators 44
- 10/100 BASET Port 44
- DEBUG Port 45
- Operating Instructions 46
- PMC Slots 47
- 3Functional Description 49
- (RST) and Abort (ABT) 50
- General Description 52
- Block Diagram 52
- (PHB) ASIC 55
- PCI Bus Latency 56
- 3:1 clock ratio: 56
- PPC Bus Latency 58
- Assumptions 60
- SDRAM Memory 62
- Functional Description 66
- Flash Memory 67
- Ethernet Interface 70
- VMEbus Interface 73
- Asynchronous Debug Port 73
- PCI Host Bridge (PHB) 75
- Interrupt Controller (MPIC) 76
- Programmable Timers 76
- 4Programming the MVME240x 79
- Processor Bus Memory Map 80
- PCI Local Bus Memory Map 81
- VMEbus Memory Map 81
- Programming Considerations 82
- Interrupt Handling 84
- DMA Channels 86
- Sources of Reset 86
- Endian Issues 88
- Programming the MVME240x 90
- PPCBug Overview 91
- PPCBug Basics 91
- Diag> 92
- Memory Requirements 93
- PPCBug Implementation 93
- Debugger Commands 96
- Table 5-1. Debugger Commands 97
- Diagnostic Tests 100
- Using PPCBug 101
- 6Modifying the Environment 103
- Modifying the Environment 104
- ENV - Set Environment 105
- ∗ signal after 107
- ∗ signal during board 107
- 00001000? 111
- (Default) 112
- Ordering Related 119
- Documentation 119
- Manufacturers’ Documents 120
- Document Title and Source 121
- Publication 121
- Related Specifications 123
- Specifications 127
- Table B-1. MVME240 128
- Specifications (Continued) 128
- Cooling Requirements 129
- EMC Regulatory Compliance 130
- CConnector Pin Assignments 131
- VMEbus Connector - P1 132
- Connector Pin Assignments 133
- VMEbus Connector - P2 134
- Pin Assignments 136
- CPU Debug Connector - J1 137
- PCI Expansion Connector - J6 142
- DTroubleshooting the MVME240x 151
- Solving Startup Problems 152
- Troubleshooting the MVME240x 153
- Numerics 169
- Single Board Computer 177
Produits connexes et manuels pour Processeurs Motorola MVME2400 Series
Processeurs Motorola DSP56800 Spécifications
(28 pages)
(28 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.848 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels