Motorola Two Way Radio KEM-ML36801A Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Stations de radio Motorola Two Way Radio KEM-ML36801A. Motorola Two Way Radio KEM-ML36801A User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Two-Way Radio
User Guide
MD Series
Safety and General Information
Licensing Information
Control Buttons
KEM-ML36801A
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general
population/uncontrolled environment exposure limits, always adhere to
the following procedure:
• Transmit no more than 50% of the time.
• To receive calls, release the Push-to-Talk (PTT) button.
• To transmit (talk), press the PTT button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting (in
terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
• United States Federal communications Commission, Code of Federal
Regulations; 47CFR part 2 sub-part J.
• American National Standards Institute (ANSI)/Institute of Electrical
and Electronic Engineers (IEEE) C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE) C95.1-1999
Edition.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998.
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
to Radiofrequency Electromagnetic Fields in the Frequency Range
from 3 KHz to 300 GHz, 1999.
• Australian communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
Getting Started
Display Screen Guide
Installing the Batteries
Each radio uses 1 NiMH rechargeable battery pack or 3 AA alkaline
batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you.
5. Reposition the battery cover and press down to secure.
Installing the Three AA Alkaline Batteries (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
3. Insert the three AA alkaline batteries with + and - polarity as shown
inside.
4. Reposition the battery cover and press down to secure.
Radio Battery Meter
The radio battery icon shows the radio battery charge level, from full
to empty . When the radio has one segment left, the radio
chirps periodically or after releasing (Low Battery Alert).
Talking and Listening
To communicate, all radios in your group must be set to the same
channel.
1. To talk, press and hold .
2. When you are finished talking, release .
For maximum clarity, hold the radio two to three inches away from your
mouth and speak directly into the microphone. Do not cover the
microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Note: This radio does not have Interference Eliminator Codes. To
communicate with radios that use Interference Eliminator Codes, the
Interference Eliminator Code must be set to 0.
Monitor Button
Pressing and holding for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows you to
adjust the volume, if necessary. You can also press to check for
activity on the current channel before you talk.
Push-to-Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you press
for 60 continuous seconds.
For More Information
For further information, you may call Motorola Solutions, Inc. at
1-800-638-5119 (U.S. and Canada), e-mail us at giantintl@callcenter.com
or visit us on the Internet at www.motorolasolutions.com.
•
ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
T
o ensure optimal radio performance and make sure human exposure
t
o radio frequency electromagnetic energy is within the guidelines set
f
orth in the above standards, always adhere to the following
p
rocedures.
Portable Radio Operation and EME Exposure
Antenna Care
U
se only the supplied or an approved replacement antenna.
U
nauthorized antennas, modifications, or attachments could damage
the radio and may violate FCC regulations.
D
o NOT hold the antenna when the radio is “IN USE.” Holding the
a
ntenna affects the effective range.
Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
g
uidelines, if you wear a radio on your body when transmitting, always
p
lace the radio in a Motorola-supplied or approved clip, holder, holster,
case or body harness for this product. Use of non-Motorola-approved
accessories may exceed FCC/Health Canada RF exposure guidelines.
I
f you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use position,
e
nsure the radio and its antenna are at least 1 inch (2.5 cm) from your
b
ody when transmitting.
D
ata Operation
If applicable, when using any data feature of the radio with or without
a
n accessory cable, position the radio and its antenna at least one
i
nch (2.5 cm) from the body.
A
pproved Accessories
53724: Remote Speaker with Push-to-Talk Microphone
53727: Earbud with Push-to-Talk Microphone
5
3728: Flexible Ear Receiver
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
i
nterference (EMI) if inadequately shielded, designed or otherwise
c
onfigured for electromagnetic compatibility. This device complies with
Part 15 of the FCC Rules.
O
peration is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
F
acilities
T
o avoid electromagnetic interference and/or compatibility conflicts,
turn off your radio in any facility where posted notices instruct you to
do so. Hospitals or health care facilities may be using equipment that is
s
ensitive to external RF energy.
A
ircraft
When instructed to do so, turn off your radio when onboard on aircraft.
Any use of a radio must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
consistent with the independent research by and recommendations of
the U.S. Food and Drug Administration.
People with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential for
interference.
• Turn the radio OFF immediately if there is any reason to suspect that
interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In
the event of such interference, you may want to consult your hearing
aid manufacturer to discuss alternatives.
Medical Devices - Other
If you use any other personal medical device, consult the manufacturer
of your device to determine if it is adequately shielded from RF energy.
Your physician may be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area
where you drive, and always obey them. If you do use your radio while
driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving
conditions so require.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your ability to
safely participate in such activities. Always use technology safely.
Do not place a portable radio in the area over an air bag or in the air
bag deployment area. Air bags inflate with great force. If a portable
radio is placed in the air bag deployment area and the air bag inflates,
the radio may be propelled with great force and cause serious injury to
occupants of the vehicle.
Potentially Explosive Atmospheres
T
urn off your radio prior to entering any area with a potentially explosive
a
tmosphere. Only radio types that are especially qualified should be used
in such areas as “Intrinsically Safe.” Do not remove, install or charge
b
atteries in such areas. Sparks in a potentially explosive atmosphere can
c
ause an explosion or fire resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to above
i
nclude fueling areas such as below decks on boats, fuel or chemical
t
ransfer or storage facilities, areas where the air contains chemicals or
p
articles (such as grain, dust or metal powders) and any other area
where you would normally be advised to turn off your vehicle engine.
A
reas with potentially explosive atmospheres are often—but not
a
lways—posted.
B
lasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
a
reas posted “Turn off two-way radios.” Obey all signs and instructions.
O
perational Cautions
A
ntennas
Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with your skin, a minor burn can result.
B
atteries
A
ll batteries can cause property damage and/or bodily injury such as
burns if a conductive material—like jewelry, keys or beaded
chains—touch exposed terminals. The conductive material may
c
omplete an electrical circuit (short circuit) and become quite hot.
E
xercise care in handling any charged battery, particularly when placing
i
t inside a pocket, purse or other container with metal objects.
E
xercise care when removing NiMH or AA batteries. Do not use sharp or
c
onductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
S
ave these Instructions
1. Do not expose the charger to rain or snow.
2
. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3
. Never alter the AC cord or plug provided with the unit. If the plug will
n
ot fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric shock.
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC receptacle.
5
. To reduce the risk of electric shock, unplug the charger from the outlet
b
efore attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped over
or subjected to damage or stress.
8
. An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire and/or
electric shock. If an extension cord must be used, make sure that:
• The pins on the plug of the extension cord are the same number, size
and shape as those on the plug of the charger.
• The extension cord is properly wired and in good electrical condition.
• The extension cord size is 18 AWG for lengths up to 100 feet, and
16 AWG for lengths up to 150 feet.
9. The supply cord of the AC adaptor cannot be replaced. If the cord is
damaged, call customer service at 1-800-638-5119 or e-mail us at
giantintl@callcenter.com.
Your Motorola radio operates on FRS & GMRS frequencies in Canada &
in the USA. For Canadian citizens, use of these frequencies is subject to
the rules & regulations of Industry Canada (IC). IC requires no license
when operated in Canada. For USA citizens, use is subject to the rules
and regulations of the Federal Communications Commission (FCC) . The
FCC requires that all operators using GMRS frequencies obtain a radio
license before operating their equipment. To obtain the FCC forms, please
visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to
source form 605 and 159, which includes all the instructions you will
need. If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
Changes or modifications not expressly approved by Motorola may void
the user’s authority granted by the IC/FCC to operate this radio and
should not be made. To comply with IC/FCC requirements, transmitter
adjustments should be made only by or under the supervision of a person
certified as technically qualified to perform transmitter maintenance and
repairs in the private land, mobile and fixed services as certified by an
organization representative of the user of those services. Replacement of
any transmitter component (crystal, semiconductor, etc.) not authorized
by the IC/FCC equipment authorization for this radio could violate IC/FCC
rules.
Note:
Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
Continued on back
MD Series
R
emoving the NiMH Battery Pack
1
. Turn the radio off.
2
. With the back of the radio facing you, lift the battery latch up to
r
elease the battery cover and remove the cover.
3
. Gently remove the NiMH battery by easing it out.
4. Reposition the battery cover and press down to secure.
R
emoving the Three AA Alkaline Batteries (Optional Accessory)
1
. Turn the radio off.
2
. With the back of the radio facing you, lift the battery latch up to
r
elease the battery cover and remove the cover.
3
. Remove each alkaline battery by easing each battery out
i
ndividually.
4
. Reposition the battery cover and press down to secure.
Notes:
• Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
•
Remove the batteries before storing your radio for extended periods
o
f time. Batteries corrode over time and may cause permanent
d
amage to your radio.
U
sing the Plug-in Charging Adaptor
T
he battery plug-in charger (adaptor) provides charging convenience
for NiMH batteries in one or both radios. Charge the NiMH battery
overnight (at least 16 hours) before using it for the first time. After the
initial charge, an empty battery is fully charged within 14 hours.
1
. Follow the steps above to install a NiMH battery pack.
2
. Connect the AC power adaptor plug into the recharging jack at the
b
ottom of the radio. (The adaptor charges two radios.)
3. Plug the AC power supply into a standard wall outlet.
N
otes:
•
The battery icon will scroll while the battery pack is being charged.
• When moving between hot and cold temperatures, do not charge
the battery until the battery temperature acclimates (usually about
20 minutes).
• For optimal battery life, unplug the charging adaptor within 16 hours.
D
o not store the radio while connected to the charger.
Low Battery Alert
In addition to your battery meter showing how much battery power you
have, your radio will beep to alert you to the fact that your batteries are low.
A
ttaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning Your Radio On and Off
1. To turn on, press and hold until a channel number appears
and the radio beeps.
2. To turn off, press and hold until the display goes blank.
Setting the Volume
Press to increase or to decrease the volume. The volume level
flashes and
VOL displays.
For a fax:
Contact the
Fax-0n-Demand
system
For mail service:
Call the FCC
Forms Hotline
If you have
questions about
the FCC License:
Call the FCC
1-202-418-0177 1-800-418-FO RM
(3676)
1-888-CALL-F CC
(225-5322)
PTT
PTT
PTT
PTT
PTT
PTT
PTT
Line Drawing best fitting for UG
PTT
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
P
TT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
P
TT
Date: Aug 26, 2011_Rev.1
M
odel: MD200
D
escription: Line Drawing with point lines
S
cale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
PTT
Date: Aug 26, 2011_Rev.1
Model: MD200
Description: Line Drawing with point lines
Scale 1 : 1 for radio size
PTT
Line Drawing best fitting for UG
MD_Series_US.qxd:Layout 1 2/6/12 12:25 PM Page 1
1
2
Résumé du contenu
Page 1 - Scale 1 : 1 for radio size
Two-Way RadioUser GuideMD SeriesSafety and General InformationLicensing InformationControl ButtonsKEM-ML36801AImportant Information on Safe and Effi
Page 2 - Channels and Frequencies
MENU MD SeriesProducts CoveredProducts and Accessoriesasdefined above, unless otherwiseprovided for below.1. Consumer Two-Way RadioAccessories.2. Pr
Produits connexes et manuels pour Stations de radio Motorola Two Way Radio KEM-ML36801A
(14 pages)
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.278 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels