Document No.: 536006-002Connected Home SolutionsDSR-4410MD Commercial Satellite Multiplex Decrypter Operator Guide
6 Figure 2-2: DSR-4410MD Back Panel (Detailed)AC 100-240V 50/60/Hz 60 WTVPass® CardETHERNETGIG E10/ 1 00RF IN 0ASI I N ASI O UT 1VIDEO OUTPRIMARY
7 Unpacking And MountingThe shipping carton contains the DSR-4410MD, two quick disconnect terminals, a power cord, and this Operator Guide.The Satel
8 For best quality audio, please take care to ground the shield on both the Satellite Multiplex Decrypter GND terminal and at the channel modulator en
9 3Operating the DSR-4410MDAll operations described in this chapter require use of the front panel, as shown in Figure 3-1.Figure 3-1: DSR-4410MD Fro
10 Using The Front PanelThe front panel LCD screen displays a series of menus that can be used to configure and control the system. The name of the cu
11 Even though the keypad options shown on the LCD screen may change for each menu and for each field, the control buttons basically do the same thi
12 About MenuThe front panel LCD displays the About menu when the DSR-4410MD is initially plugged in or after a factory reset. This menu identifies th
13 Pressing the ENTER button when the cursor is on a menu name causes the cursor to return to the main, top level menu. The charts on the following
14 E 192.168.000.100PORT 10/100 IP Address E 192.168.000.001PORT 10/100
15 Diagnostic Menus E Fact1 00 0 NoDIAG Menus ACP KS Clr E
OPERATION PRECAUTIONSWARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.The lightning flash with the arrowhead
16 Installation MenusThe purpose of the installation menus is to configure the ports and choose settings that remain fixed over a period of time. This
17 Input FieldThe Input field displays the input to which the receiver is currently tuned. It allows manual selection of Ports 0 and 1 or the ASI in
18 Xpndr FieldThis field allows selection of an initial satellite transponder number and can only be used if the Xpndr option in the Mode field is sel
19 This menu is not available when the ASI In option is selected. That option is located in the Manual Tune menu (described on page 16).This menu, t
20 Symbol/Code/Format FieldPress the button until the cursor is at the Symbol label, and press the ENTER button to move into the field. Press the butt
21 This field displays the satellite to which the port is related and is not editable when the Mode field is set to Auto. This field displays dashes
22 Use the ACP menu to assign services in the input multiplex to specific ACPs. The fields are defined below: No The ACP Slot number (0 - 63). There a
23 To manually assign a service to an ACP Slot: 1. Navigate to the ACP menu in the Installation menu and press ENTER.2. Press to scroll to Mode and
24 Press the buttons until an Audio1 menu or Audio2 menu appears. These menus have three fields that allow the user to customize the audio output base
25 The DSR-4410MD now seeks to have a language defined for both left and right dual mono outputs.• By pressing the ENTER button (ignoring the cautio
Chapter 1 Introducing the DSR-4410MD ... 1Key
26 Press the buttons until the Audio1 Gain menu or Audio2 Gain menu appears. These menus allow adjustment of the analog audio signal output level from
27 Press the button until the Alarm menu is located. This menu allows the user to set up different bypass modes in case the DSR-4410MD goes into an
28 Press the buttons until the ASI Output menu appears. This menu allows the user to configure the digital ASI output. It is used to define the form
29 Factory Defaults OptionThe Factory Defaults option allows the user to reset the system to the programming values originally set by the factory fi
30 Press the buttons until the Core menu appears. This menu allows the user to change the front panel LCD contrast, select where text (e.g., subtitl
31 Press the buttons until the Video Out Format menu appears. It has two fields that allow modification of the output format. The receiver does no
32 Press the buttons until the Aspect Ratio menu appears. It displays the current input aspect ratio and has one field that allows the output aspect r
33 Press the buttons until the Firmware menu appears. This menu displays the DSR-4410MD's firmware release information, which is equivalent to
34 Press the buttons until the DOWNLOAD menu appears. This menu allows the user to monitor the status of the current code download.During a background
35 Channel MenusPress the buttons until the Channel menu appears. This menu allows the user to select an active VCT, select the virtual channel, and
IP Menus ... 42M
36 The DSR-4410MD displays warning messages for the following three conditions:• A warning message is displayed when the user changes from a virtual c
37 Press any arrow button ( ) to back out of the field and leave it unchanged. The DSR-4410MD cannot decode the chosen virtual channel until a port
38 The DSR-4410MD displays warning messages for the following two conditions:• A warning message is displayed when the user changes from a virtual cha
39 Dspl FieldPress the button until the cursor is at the Dspl (Display) label, and press the ENTER button to move into the field. The Display field
40 • If the AudioMix option is Dual Mono and a language pair is not available that matches the user’s choice for Left and Right languages, the DSR-441
41 This Text Language menu has two fields that allow the user to modify and view the status of the language for the subtitle display. Press the butt
42 IP MenusUse the IP menus is to configure the 10/100 port.Use the following procedure to view the MAC address for the lower Ethernet port on the bac
43 Use the following procedure to set and view the IP address for the lower Ethernet port on the back panel of the DSR-4410MD. Press the buttons u
44 Use the following procedure to set and view the IP address for the lower Ethernet port on the back panel of the DSR-4410MD. Press the buttons unt
45 Use the following procedure to set and view the GigE IP address for the upper Ethernet port on the back panel of the DSR-4410MD. Press the butt
1 1Introducing the DSR-4410MDThe Motorola DSR-4410MD is a commercial Satellite Multiplex Decrypter designed for cable operators and other commercia
46 Use the following procedure to set and view the GigE Default Gateway address for the upper Ethernet port on the back panel of the DSR-4410MD. Press
47 Use the following procedure to set and view the GigE Multiple Program Transport Stream (MPTS) address for the upper Ethernet port on the back pan
48 Status Display MenusStatus display menus provide information regarding the current status of the DSR-4410MD. This menu list important Satellite Mul
49 Channel FieldThe Channel field displays the selected virtual channel number (from the Channel menu). Dashes are displayed when no information is
50 Code FieldThis field displays the code rate (error control coding for forward error correction) of the L-band signal. Dashes indicate that no infor
51 Press the buttons until the STATUS6 menu appears. This screen displays the DSR-4410MD’s memory (free memory), and Flash.Memory FieldThis status-o
52 Diagnostics MenusThe DSR-4410MD's diagnostic menus allow the user to isolate problems to the DSR-4410MD or the satellite using the front panel
53 Press the buttons until the Audio Test Signal menu appears. This menu allows the user to select an audio test signal for each of the two audio ou
54 Table 3-1: Test Pattern OptionsPress the ENTER button and a warning message appears saying that the current video display will be interrupted if t
55 Press the buttons until the Vertical Interval Test Signal (VITS) menu appears. This menu allows the user to insert VITS on lines 17 or 18. Wavefo
2 • Audio output consists of two stereo pairs. When the programmer provides multiple audio choices, the audio pair can be selected. Programmers can ta
56 Field FieldThe Field field allows the user to select the field on which the VITS is reinserted by the receiver. There are two choices, Field 1 or F
57 4TroubleshootingBefore contacting the Hotline, review Table 4-1 for problems and suggested solutions.Table 4-1: Troubleshooting SolutionsProblem P
59 5Signal FlowFigure 5-1 shows the DSR-4410MD signal flow.Figure 5-1: DSR-4410MD Signal FlowGigE Phy VECPowerSupply10/100 PhyDACCable DriverCable Dr
61 6Product SupportIf You Need HelpFor assistance with Motorola products only, contact the Motorola Technical Response Center (TRC), 24 hours a day, 7
63 7Downlink/L-band FrequencyConversion TablesA distributor or programmer can provide the latest C-band and Ku-band frequency plans at purchase time.
65 8Language AbbreviationsNote: This list of languages was recommended to system operators as the appropriate identifiers for audio, subtitle, and tex
3 DTMF Dual-Tone Multi-FrequencyDVB Digital Video BroadcastingEIA Electronic Industries AssociationEMM Entitlement Management MessageFCC Federal Com
66 Panjabi pan Portuguese porJapanese jpn Rajasthani rajJavanese jav Romanian rumKashmiri kas Russian rusKorean kor Samoan smoKurdish kur Scots scoLat
67 9DiagnosticsDiagnostic Data screens are developed by Firmware during implementation according to the needs of the system. All values update as requ
68 Fast Facts 1 [page 69]Fast Facts 1 Unit Address Diagnostics [page 71]Fast Facts 2 [page 72]Fast Facts 3 (Video) [page 73]Fast Facts 4 (Audio) [page
69 The Fast Facts screens are used as easier method of seeing diagnostic data than what is being shown in Diag-nostic Screens A-E. The Fast Facts sc
70 Total Programs Displays the total number of services in the transport stream.Service Displays the service number for the current program.Programs A
71 This diagnostic screen lists the unit addresses located on DSR-4410MD.The ACP0 (Access Control Point) unit address is located on the back of the
72 The Fast Facts 2 screen displays information relating to the port configuration of the unit.Field Name DefinitionPort number The port number being
73 The Fast Facts 3 screen displays information relating to video information.Field Name DefinitionVideo Locked An indication of video lock or unloc
74 Aspect Ratio The aspect ratio of the streamVideo Mute Count (VMC)The current video mute countFrame Rate The frame rate code of the streamPTS : FIFO
75 The Fast Facts 4 screen displays information relating to audio information. There are two columns of informa-tion displayed, one column for the f
4
76 The Fast Facts 5 screen displays information relating to Ethernet configuration.Field Name DefinitionNetwork Status Gives the status of the 10/100
77 The Fast Facts 5 (Gigabit Ethernet) screen displays information relating to Gigabit configuration.Field Name DefinitionNetwork Status Gives the s
78
79 10Specifications RFInput Frequency Range 950 to 2150 MHzInput RF Level -25 to -65 dBmRF Port Impedance 75 OhmsRF Port Return Loss 8 dB minimumPo
80 Note: Audio and data connectors may be ordered through Phoenix Contact part numbers 1840447 / 1840528. Transmission StandardDigiCipher Symbol Rat
81 ConnectorsRF In F-type (Qty 2)OSD Video Out BNC (Qty 1)Alarm Screw terminal (Qty 1)Cue Tone (Labeled: Q+ and Q-) Screw terminal (Qty 1)Audio Out
82
Caring for the Environment by Recycling When you see this symbol on a Motorola pdo not dispose of the product with residentiacommercial waste. roduct,
5 2Connecting the DSR-4410MDUnpacking And Connecting The DSR-4410MDCable connections, described in this chapter, are made to the back panel of the DSR
Motorola Connected Home Solutions6450 Sequence Dr.San Diego, CA 92121Document No: 536006-002, Rev. B
Commentaires sur ces manuels