Motorola M68CPU32BUG Manuel d'utilisateur Page 159
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DIAGNOSTIC FIRMWARE GUIDE
M68CPU32BUG/D REV 1 6-15
MT C Set Stop Address MT C
6.5.3 Set Stop Address
CPU32Diag>MT C [new value]
MT C allows the user to select the stop address used by all of the memory tests. The stop address
is the address where testing terminates, so the stop address must be set to the last address +1.
EXAMPLE
If the user supplied the optional new value, then the display appears as follows:
CPU32Diag>MT C [new value]<CR>
Stop Addr.=<new value>
CPU32Diag>
If a new value was not specified by the user, then the old value is displayed and the user
is allowed to enter a new value.
NOTE
The default is Stop Addr.=00010000, which is the end of on-board
RAM.
CPU32Diag>MT C
Stop Addr.=<current value> ?[new value]<CR>
Stop Addr.=<new value>
CPU32Diag>
This command may be used to display the current value without changing it by pressing a
carriage return <CR> without entering the new value.
CPU32Diag>MT C
Start Addr.=<current value> ?<CR>
Start Addr.=<current value>
CPU32Diag>
NOTE
If a new value is specified, it is truncated to a longword boundary
and, if less than the value of the start address, is replaced by the
start address. The stop address is never allowed to be lower in
memory than the start address. These changes occur before another
command is processed by the monitor.
- M68CPU32BUG DEBUG MONITOR 1
- USER’S MANUAL 1
- M68CPU32BUG/D 1
- TABLE OF CONTENTS 3
- M68CPU32BUG/D REV 1 ii 4
- M68CPU32BUG/D REV 1 iii 5
- M68CPU32BUG/D REV 1 iv 6
- M68CPU32BUG/D REV 1 v 7
- LIST OF FIGURES 8
- LIST OF TABLES 8
- CHAPTER 1 9
- 1.1 INTRODUCTION 9
- 1.2 GENERAL DESCRIPTION 9
- GENERAL INFORMATION 10
- M68CPU32BUG/D REV 1 1-2 10
- 1.3 USING THIS MANUAL 11
- 1.5 SYSTEM RESTART 12
- 1.6 MEMORY REQUIREMENTS 13
- Figure 1-2. BCC Memory Map 14
- M68CPU32BUG/D REV 1 1-7 15
- M68CPU32BUG/D REV 1 1-8 16
- CHAPTER 2 17
- DEBUG MONITOR DESCRIPTION 17
- 2.1 INTRODUCTION 17
- M68CPU32BUG/D REV 1 2-2 18
- M68CPU32BUG/D REV 1 2-3 19
- M68CPU32BUG/D REV 1 2-4 20
- M68CPU32BUG/D REV 1 2-5 21
- M68CPU32BUG/D REV 1 2-6 22
- M68CPU32BUG/D REV 1 2-7 23
- M68CPU32BUG/D REV 1 2-8 24
- M68CPU32BUG/D REV 1 2-9 25
- M68CPU32BUG/D REV 1 2-10 26
- M68CPU32BUG/D REV 1 2-11 27
- 2.6 FUNCTION CODE SUPPORT 28
- M68CPU32BUG/D REV 1 2-13 29
- M68CPU32BUG/D REV 1 2-14 30
- CHAPTER 3 31
- 3.1 INTRODUCTION 31
- M68CPU32BUG/D REV 1 3-2 32
- BC Block of Memory Compare BC 33
- BF Block of Memory Fill BF 35
- BM Block of Memory Move BM 37
- BR Breakpoint Insert BR 39
- BS Block of Memory Search BS 40
- BV Block of Memory Verify BV 43
- DC Data Conversion DC 45
- DU Dump S-Records DU 46
- M68CPU32BUG/D REV 1 3-19 49
- M68CPU32BUG/D REV 1 3-20 50
- GN Go To Next Instruction GN 51
- GO Go Execute User Program GO 53
- M68CPU32BUG/D REV 1 3-26 56
- M68CPU32BUG/D REV 1 3-27 57
- HE Help HE 58
- M68CPU32BUG/D REV 1 3-31 61
- M68CPU32BUG/D REV 1 3-32 62
- M68CPU32BUG/D REV 1 3-33 63
- MA Macro Define/Display MA 64
- MAE Macro Edit MAE 67
- M68CPU32BUG/D REV 1 3-39 69
- MD Memory Display MD 70
- MM Memory Modify MM 72
- MS Memory Set MS 74
- M68CPU32BUG/D REV 1 3-45 75
- M68CPU32BUG/D REV 1 3-46 76
- M68CPU32BUG/D REV 1 3-47 77
- PA Printer Attached PA 78
- PF Port Format PF 79
- RD Register Display RD 82
- RESET Cold/Warm Reset RESET 86
- RM Register Modify RM 87
- RS Register Set RS 88
- SD Switch Directories SD 89
- T Trace T 90
- M68CPU32BUG/D REV 1 3-63 93
- Trace on change of flow: 94
- TM Transparent Mode TM 95
- M68CPU32BUG/D REV 1 3-66 96
- M68CPU32BUG/D REV 1 3-67 97
- M68CPU32BUG/D REV 1 3-68 98
- M68CPU32BUG/D REV 1 3-69 99
- DEBUG MONITOR COMMANDS 100
- M68CPU32BUG/D REV 1 3-70 100
- M68CPU32BUG/D REV 1 3-71 101
- M68CPU32BUG/D REV 1 3-72 102
- CHAPTER 4 103
- ASSEMBLER/DISASSEMBLER 103
- 4.1 INTRODUCTION 103
- 4.2SOURCE PROGRAM CODING 104
- M68CPU32BUG/D 4-3 105
- M68CPU32BUG/D 4-4 106
- Pseudo Registers 107
- Main Processor Registers 107
- M68CPU32BUG/D 4-6 108
- M68CPU32BUG/D 4-7 109
- M68CPU32BUG/D 4-8 110
- M68CPU32BUG/D 4-9 111
- M68CPU32BUG/D 4-10 112
- M68CPU32BUG/D 4-11 113
- 0000D000 6000BF68 BRA *-4096 114
- 0000D000 60FE BRA.B * 114
- 0000D000 4EF90000 D000 JMP * 114
- CHAPTER 5 115
- SYSTEM CALLS 115
- 5.1 INTRODUCTION 115
- 5.2 SYSTEM CALL ROUTINES 116
- M68CPU32BUG/D REV 1 5-3 117
- M68CPU32BUG/D REV 1 5-4 118
- M68CPU32BUG/D REV 1 5-5 119
- COUNT = 3 120
- COUNT = 3? 5<CR> 120
- COUNT = 5 120
- COUNT = 3? <CR> 120
- SYSCALL .CHKBRK 121
- BEQ BREAK 121
- M68CPU32BUG/D REV 1 5-8 122
- M68CPU32BUG/D REV 1 5-9 123
- .ERASLN Erase Line .ERASLN 124
- SYSCALL .INCHR Call .INCHR 125
- M68CPU32BUG/D REV 1 5-12 126
- M68CPU32BUG/D REV 1 5-13 127
- M68CPU32BUG/D REV 1 5-14 128
- MOVE.B D0,-(A7) 129
- Send character in D0 129
- SYSCALL .OUTCHR 129
- To default output port 129
- .OUTSTR .OUTSTR 130
- M68CPU32BUG/D REV 1 5-17 131
- PEA (A0) 132
- Long buffer address 132
- SYSCALL .READLN 132
- M68CPU32BUG/D REV 1 5-19 133
- SYSCALL .RETURN 134
- Return to CPU32Bug 134
- .SNDBRK Send Break .SNDBRK 135
- M68CPU32BUG/D REV 1 5-22 136
- SYSCALL .TM_INI 137
- Initialize timer 137
- .TM_RD Read Timer .TM_RD 138
- SYSCALL .TM_STR0 139
- Start Timer at T=0 .TM_STR0 140
- .WRITDLN .WRITDLN 141
- .WRITELN .WRITELN 143
- CHAPTER 6 145
- DIAGNOSTIC FIRMWARE GUIDE 145
- 6.1 INTRODUCTION 145
- 6.2 DIAGNOSTIC MONITOR 145
- M68CPU32BUG/D REV 1 6-2 146
- M68CPU32BUG/D REV 1 6-3 147
- 6.3 UTILITIES 148
- M68CPU32BUG/D REV 1 6-5 149
- CPU CPU Tests For The MCU CPU 150
- CPU A Register Test CPU A 151
- CPU B Instruction Test CPU B 152
- CPU C Address Mode Test CPU C 153
- M68CPU32BUG/D REV 1 6-10 154
- MT Memory Tests MT 155
- M68CPU32BUG/D REV 1 6-12 156
- MT A Set Function Code MT A 157
- MT B Set Start Address MT B 158
- MT C Set Stop Address MT C 159
- MT D Set Bus Data Width MT D 160
- MT E March Address Test MT E 161
- MT F Walk a Bit Test MT F 162
- MT G Refresh Test MT G 163
- MT H Random Byte Test MT H 164
- MT I Program Test MT I 165
- MT J Test and Set Test MT J 166
- BERR Bus Error Test BERR 167
- M68CPU32BUG/D REV 1 6-24 168
- APPENDIX A 169
- S-RECORD INFORMATION 169
- A.1 INTRODUCTION 169
- A.2 S-RECORD CONTENT 169
- A.3 S-RECORD TYPES 170
- A.4 S-RECORDS CREATION 171
- M68CPU32BUG REV 1 A-4 172
- APPENDIX B 173
- SELF-TEST ERROR MESSAGES 173
- B.1 INTRODUCTION 173
- M68CPU32BUG REV 1 B-2 174
- APPENDIX C 175
- USER CUSTOMIZATION 175
- C.1 INTRODUCTION 175
- C.2 CPU32BUG CUSTOMIZATION 176
- M68CPU32BUG REV 1 C-3 177
- C>DEL TMP.MX<CR> 178
- C>DEL C32B1.MX<CR> 178
- C.3 CUSTOMIZATION TABLE 179
- M68CPU32BUG REV 1 C-6 180
- M68CPU32BUG REV 1 C-7 181
- ROM AUTO BOOT VECTORS 182
- Periodic Interrupt Timer 183
- M68CPU32BUG REV 1 C-10 184
- M68CPU32BUG REV 1 C-11 185
- M68CPU32BUG REV 1 C-12 186
- M68CPU32BUG REV 1 C-13 187
- C.4 COMMUNICATION FORMATS 188
- M68CPU32BUG REV 1 C-15 189
- M68CPU32BUG REV 1 C-16 190
- Platform Board 191
- M68CPU32BUG REV 1 C-18 192
- Offset Value Comment 193
- M68CPU32BUG REV 1 C-20 194
- M68CPU32BUG REV 1 C-21 195
- M68CPU32BUG REV 1 C-22 196
Produits connexes et manuels pour Téléviseurs et moniteurs Motorola M68CPU32BUG
(35 pages)
(120 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels