Motorola AT Commands G24-L Informations techniques Page 382
- Page / 680
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Modem Configuration and Profile
3-294 AT Commands Reference Manual August 5, 2008
Two modes exist:
• Idle mode: The G24 has no data to send.
• Wakeup mode: The G24 has data to send to the terminal.
After the G24 changes the line edge to Wakeup mode, there will be a delay (the default is 30 ms)
sent by the ats102 command before sending any data to the terminal (using RS232 protocol).
Figure 3-12: Sleep Mode when S24 > 0
Figure 3-13: G24 Lines when S24 > 0
S24, Set Number of Seconds Delay Before G24 Enters Sleep Mode
This command activates/disables the Sleep mode. The terminal sends ATS24=5, and if there are
no radio and UART activities, the G24 enters sleep mode in 5 seconds.
If terminal has some indication of the CTS pin activity, it can see:
• If +MSCTS=0 (default), the line changes its state periodically. (For more information refer to
“+MSCTS, Enable/Disable CTS During Wakeup Period” on page 3-296.)
• If +MSCTS=1, the line is switched off at the moment of entering Sleep mode and stays off
even if G24 is awakened.
G24 CTS
(Defaultwhen
at+mscts=0)
G24
Sleepmode
(Clock)
TerminalTXD
Awake
Sleep
S24 Less than S24
WAKEUP-IN
30 ms
S24
30 ms
G24 TXD
WAKEUP-OUT
S102S102
- Technical Information 1
- Copyrights 2
- Computer Software Copyrights 2
- Trademarks 3
- Table of Contents 5
- Table of Contents 10
- List of Figures 17
- List of Figures 18
- List of Tables 19
- List of Tables 20
- Manual Scope 25
- Target Audience 25
- Manual Organization 25
- Applicable Documents 26
- Contact Us 26
- Text Conventions 26
- General Safety 27
- Caring for the Environment 28
- Limitation of Liability 29
- Warranty Notification 29
- Claiming 30
- Conditions 31
- Installed Data 32
- Out of Warranty Repairs 32
- Revision History 33
- Revision History (Cont.) 34
- Version Date Issue Remarks 34
- Chapter 1: Product Features 35
- CSD Operation 36
- Improved OEM Features 37
- Set up Idle Mode Text 38
- Menu Selection 38
- Call Control by SIM 38
- TCP/UDP IP Connection 39
- Chapter 1: Product Features 41
- Online Data Mode 42
- Features and Benefits 43
- FTP Connection 44
- Manage FTP Connection 45
- Manage Remote File System 46
- File Transfer Operations 46
- Other FTP Operations 47
- Overview 48
- Suppression 49
- MUX Integration 50
- Technical Description 51
- Short Message Service (SMS) 52
- POP3 Email 54
- Character Sets 56
- AT Commands Summary 58
- AT Commands Overview 73
- AT Commands Protocol 74
- AT Commands Structure 75
- Results Code Structure 76
- Command Token Types 78
- Command Argument Types 79
- Command Mode Types 79
- Aborting Commands 80
- Core AT Commands 81
- +FTPCDUP 83
- +FTPCLOSE 83
- Modem ID 89
- Command Response/Action 91
- Table 3-2: +CSCS Parameters 93
- +CIMI, Request IMSI 94
- +CNUM, Request MSISDN(s) 95
- Read Command 96
- Table 3-3: +CNUM Parameters 96
- Capability Reporting 98
- Receiving a Data Call 100
- Call Control AT Commands 101
- DL, Dial Last Number 104
- H, Hang-up Call 105
- A, Answer Incoming Call 107
- Indication 107
- Table 3-7: +CRC Parameters 108
- RING/+CRING Indication 108
- Table 3-8: +CLIP Parameters 110
- +CCWA, Call Waiting Command 111
- Table 3-9: +CCWA Parameters 112
- Table 3-11: 115
- • Provisioned permanently 119
- Table 3-13: +CLIR Parameters 120
- &Q, Asynchronous Mode 123
- +CHUP, Hang Up Call 123
- Connection of a Voice Call 126
- Table 3-17: +MFIC Parameters 129
- +MHUP, Motorola Hung UP call 130
- AT+MTTY=? 133
- +MTTY: (0-3) 133
- AT+MTTY=1 133
- Call Status Messages 134
- +CLCC, List Current Calls 135
- Execute command enables 135
- Table 3-22: +CLCC Parameters 136
- +MCST, Call Status Messages 137
- +MCST Parameters 138
- Table 3-23: +MCST Parameters 138
- +TCLCC, List Current Calls 139
- Table 3-24: +TCLCC Parameters 140
- Table 3-25: +MNTFY Parameters 142
- +CAOC, Advice of Charge 143
- +CACM, Accumulated Call Meter 145
- Table 3-28: +CAMM Parameters 147
- +CR=[<mode>] OK 149
- +CR? +CR:<mode> 149
- +CR=? +CR:<mode> 149
- Supplementary Services 150
- Table 3-31: 151
- +CSSN Parameters 151
- Table 3-35: 155
- Table 3-36: +COLP Parameters 158
- Table 3-37: +CPBS Parameters 160
- +CSVM, Set Voice Mail Server 165
- Table 3-42: +MDSI Parameters 168
- Table 3-43: +MCSN Parameters 171
- +MDBR, Read Date Book Entries 177
- Table 3-47: +MDBR Parameters 178
- +MDBW, Write Date Book Entry 179
- Table 3-48: +MDBW Parameters 180
- Table 3-49: +MDBWE Parameters 182
- Table 3-50: +CCLK Parameters 185
- SMS Commands 186
- +CMGF, Message Format 189
- Table 3-54: + 190
- Table 3-55: +CSCA Parameters 191
- Table 3-56: +CSMP Parameters 192
- Table 3-58: +CSDH Parameters 194
- Indication) 198
- <Parameter> Description 201
- +CMGL, +MMGL, List Messages 202
- Table 3-65: 204
- +CGML/+MMGL Parameters 204
- +CMGR, +MMGR, Read Message 206
- Table 3-66: 207
- +CGMR/+MMGR Parameters 207
- GSM03.40) 209
- GSM03.40) (Cont.) 210
- Reserved bits are ignored 211
- Table 3-70: <fo> f 211
- +MMAR, Motorola Mark As Read 213
- +CMGD, Delete Message 220
- +CMGS, Send SM to Network 222
- Table 3-83: 226
- +MCSAT Parameters 226
- + MEDT? +MEDT: <mode> 228
- AT+MEDT=? +MEDT: (list of 228
- Table 3-84: +MEDT Parameters 229
- • SMS-DELIVER 231
- • SMS-STATUS-REPORT 231
- • CBM (broadcast message) 231
- DCS handling 233
- Examples: 235
- Email Services AT Commands 238
- Table 3-90: +MEMAS Parameters 240
- Table 3-91: +MEMGS Parameters 242
- Example: 243
- Table 3-92: +MEMDE Parameters 244
- +MEMSE, Send Email Message 245
- +MEML, List Email Messages 248
- +MEMR, Read Email Message 251
- +MEMD, Delete Email Message 252
- Table 3-97: +MEMD Parameters 253
- +MEGA, Email Gateway Address 255
- AT+MEGA? 256
- +MEGA: "4252833433" 256
- Network Commands 257
- +CRLP, Radio Link Protocol 258
- Table 3-102: +CREG Parameters 259
- +COPS, Operator Selection 262
- Table 3-104: +COPS Parameters 264
- +CPOL, Preferred Operators 265
- Table 3-107: +MFS Parameters 269
- Table 3-108: + 271
- MCELL Parameters 271
- Cell Resel 273
- T3212 Routing 273
- Multiband Reporting 273
- Cell Resel. offset MaxTxPow 275
- Table 3-123: 278
- EFEM Parameters 278
- Power offset in dBm 280
- Table 3-125: +MCI Parameters 284
- +MJDC, Jamming Detection 285
- Table 3-126: +MJDC Parameters 286
- Hardware Information 288
- +CBAUD, Baud Rate Regulation 289
- +MTDTR, DTR Line Test Command 292
- +MTCTS, CTS Line Test Command 293
- &K, RTS/CTS Flow Control 293
- &C, Circuit 109 Behavior 294
- &D, Circuit 108 Behavior 296
- +MCWAKE, GPRS Coverage 297
- ATS97, Antenna Diagnostic 301
- +MRST, Perform Hard Reset 302
- +TWUS, Wakeup Reason Set 302
- +TWUR, Wakeup Reason Request 304
- +TASW, Antenna Switch 304
- +MIOC, Motorola I/O Configure 308
- Table 3-143: + 309
- MIOC Parameters 309
- Light control example: 310
- +MIOD, Motorola I/O Define 312
- Table 3-144: + 313
- MIOD Parameters 313
- Table 3-145: Keypad GPIOs 313
- Table 3-146: +MMAD Parameters 316
- +MPCMC, Continuous PCM Clock 321
- Audio Setup 325
- Basic Audio Setup 326
- Advanced Audio Setup 326
- Basic Audio Setup Commands 327
- +CLVL, Loudspeaker Volume 328
- S94, Sidetone Effect 330
- S96, Echo Canceling 331
- +MAPATH, Audio Path 332
- Figure 3-7: Audio Paths 333
- +MAVOL, Volume Setting 335
- +MAMUT, Input Devices Mute 337
- +MAFEAT, Features Selection 338
- General Audio Commands 339
- +CALM, Alert Sound Mode 340
- +CRTT, Ring Type Selection 342
- Table 3-167: +CRTT Parameters 343
- +VTD, Tone Duration 345
- Access Control Commands 347
- Unblocking SIM Card 348
- Table 3-172: +CPIN Parameters 349
- +CPWD, Change Password 353
- +CLCK, Facility Lock 354
- Table 3-176: +CLCK Parameters 355
- Table 3-177: +EMPC Parameters 358
- Command 360
- Web-Session default entry 360
- Automatic/Non-Automatic 362
- New Bootstrap Process 368
- AT+MFOTABS OK 369
- +CME ERROR 369
- Modem Register Commands 370
- Q, Result Code Suppression 371
- E, Command Echo 372
- S, Bit Map Registers 374
- Table 3-188: S2 Parameters 376
- \G, Software Control 377
- \J, Terminal Auto Rate 377
- \N, Link Type 377
- +CBAND, Change Radio Band 377
- Sleep Mode Commands 379
- Sleep Mode AT Commands 380
- Sleep Mode HW Signals 380
- WAKEUP-IN 381
- Line (pin #16) 381
- Line (pin #21) 381
- Error Handling Commands 386
- Table 3-196: +CMEE Parameters 387
- Table 3-197: +CME Errors 388
- Table 3-198: +CM 390
- S Errors 390
- Table 3-199: +STK Errors 391
- +CEER, Extended Error Report 393
- Table 3-200: +CEER Parameters 394
- Table 3-201: + 397
- MGEER Parameters 397
- UI (User Interface) 399
- Table 3-202: +CRSM Parameters 400
- &V, View Configuration 404
- &W, Store User Profile 405
- AT&W0 406
- AT&W1 406
- &Y, Default User Profile 407
- +CKPD, Keypad Control 407
- +CME ERROR: <err> 408
- Table 3-208: +MKPD Parameters 410
- Table 3-209: +CMER Parameters 411
- +CLAN, ME Language 412
- +CIND, Indicator Control 413
- Table 3-211: +CIND Parameters 414
- +CKEV, Key Press Echo Output 417
- +MUPB, Phone Book Event 419
- GPRS/EDGE 420
- +CGDCONT, Define PDP Context 422
- For example: 423
- +CGATT, GPRS Attach or Detach 427
- Table 3-222: D*99 Parameters 430
- +CGPRS, GPRS Coverage 431
- CGPADDR, GPRS ADDResses 433
- +MDLC, Dial Local Connection 434
- +MIAU, IP Addresses Utility 435
- Table 3-226: +MIAU Parameters 436
- EDGE Commands 437
- Table 3-227: 440
- +CGEQREQ Command Parameters 440
- Table 3-228: 446
- +CGEQMIN Command Parameters 446
- +CGEQNEG - (Negotiated) 449
- Table 3-229: 450
- +CGEQNEG Command Parameters 450
- +MCEG, Motorola Control EGPRS 453
- Customer 454
- Application 454
- STK Mechanisms 455
- +MTKR, Profile Download 455
- Profile Structure 456
- Table 3-254: + 467
- Send DTMF 471
- Language Codes 476
- +MTKM, Motorola ToolKit Menu 480
- Control are modified 482
- Table 3-262: +MTKC Parameters 482
- Table 3-283 487
- +MIPCLOSE, Close a Socket 490
- +MIPSEND, Send Data 493
- +MIPSTAT, Status Report 498
- Pseudo-command Mode 499
- MIPXOFF, Flow Control - Xoff 499
- MIPXON, Flow Control - Xon 500
- • Power Up - 0 502
- Table 3-276: 505
- +MPING Command Parameters 505
- Table 3-278: 508
- +MSDNS, Set DNS IP Address 510
- Table 3-281: + 516
- MIPCFF Parameters 516
- Table 3-282: 518
- +MIPSSL Parameters 518
- Table 3-283: +MIPSSL Alerts 518
- FTP (File Transfer Protocol) 520
- +FTPMKD, Make Directory 526
- +FTPRMD, Remove Directory 527
- +FTPCDUP, Change Directory Up 529
- +FTPDEL, Delete File 529
- +FTPREN, Rename File 530
- +FTPLIST, Request List 532
- +FTPSTAT, Request Status 533
- +FTPNOOP, No Operation 536
- NOP - Compatible 540
- Fax Class 1 541
- Fax Commands 542
- +FTS, Transmit Silence 543
- +FRS, Receive Silence 543
- +FTM, Transmit Data 544
- +FRM, Receive Data 546
- +FRH = <MOD> CONNECT 548
- NO CARRIER 548
- +FPR, Fax Serial Port Rate 550
- RS232 Multiplexer Feature 552
- Product Architecture 553
- MUX States Overview 553
- PREMUX State 554
- UART Flow Control 555
- +CMUX, MUX Startup Command 556
- MUX Modes 557
- Basic MUX Channel Definitions 558
- Channel Priorities 558
- Two virtual channels– G24 559
- • PCHS: Per channel setting 560
- • PCHS: 560
- Unsolicited 569
- -special 569
- Multiple Channel Definitions 572
- GPRS Definitions 572
- Chapter 4: Using the Commands 575
- GPRS VoiceCSD Data 576
- G24 Network Connection 577
- Test G24 Communication 577
- G24 Phonebook Download 577
- Status (Optional) 577
- RS232 Lines Setup 578
- Basic Configuration 579
- 1. Baud setting example: 580
- AT+CPIN? 581
- See Developer’s Guide 581
- +CPIN: READY 581
- Terminal Synchronization 583
- Dialing Using ATD 588
- Voice Call Manipulations 590
- Conference Call 591
- Data Call 592
- Establishing GPRS PDP Context 593
- Using the ATD* Command Set 594
- Changing the Character Set 595
- Less then S24 596
- Get Inkey 597
- Get Input 598
- Play Tone 598
- Set Up Menu 599
- Select Item 599
- Send SMS 599
- Set Up Call 600
- Call Control 600
- Launch Browser 601
- Setup Event List 602
- TCP Data Transfer Example 603
- Xoff and Xon Example 605
- Terminal 607
- Handsfree 607
- (Non-Transparent Mode) 608
- Chapter 5: Tools 611
- Using WinFAX 612
- Appendix A: Reference Tables 613
- Functionality 635
- Symbol GSM (GSM 03.38) 645
- Appendix B: MUX 655
- MUX State 656
- MUX UART Port Speed 657
- MUX State Procedures 659
- UIH Frames 660
- Test UIH Control Frames 660
- MUX Customer Packet 661
- Mux 0710 Packet 662
- MUX Open Service 664
- MUX Close Service 664
- Data Transfer 664
- Acronyms and Abbreviations 665
- Abbreviation Full Name 667
- Numerics 671
- B - C Index 673
- H - M Index 675
- T - W Index 677
- @6889192V28@ 680
Produits connexes et manuels pour Mise en réseau Motorola AT Commands G24-L
(21 pages)
(13 pages)
(185 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels