Motorola AT Commands G24-L Informations techniques Page 383
- Page / 680
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3: AT Commands Reference
August 5, 2008 AT Commands Reference Manual 3-295
The following table shows the S24 parameters.
Example
ATS24? <enter>
000
OK
ATS24=5 <enter>
OK
ATS24? <enter>
005
OK
(If there are no radio and UART activities, the G24 will enter sleep mode in 5 seconds)
S102, Set Delay Before Sending Data to the Terminal
This command sets the value of the delay before sending data to the terminal. Before receiving
data, the terminal connected to the G24 will receive:
• Terminal Wakeup signal (the Wakeup Out Line (pin #26) state will be active low).
• A delay that is equal ATS102 value.
• Data (GPRS, CSD, AT commands' echo and results, unsolicited reports).
Command Type Syntax Response/Action Remarks
Set
ATS24=[<value>] OK
The Set command sets the amount of
time, in seconds, the G24 should wait
before entering Sleep mode.
Read
ATS24? <value>
OK
The Read command returns the current
value.
Table 3-192: S24 Parameters
<Parameter> Description
<value> Number of seconds (0 <= n <= 255)
0 Disable Sleep mode
>0 Enable Sleep mode
The default value is 0.
- Technical Information 1
- Copyrights 2
- Computer Software Copyrights 2
- Trademarks 3
- Table of Contents 5
- Table of Contents 10
- List of Figures 17
- List of Figures 18
- List of Tables 19
- List of Tables 20
- Manual Scope 25
- Target Audience 25
- Manual Organization 25
- Applicable Documents 26
- Contact Us 26
- Text Conventions 26
- General Safety 27
- Caring for the Environment 28
- Limitation of Liability 29
- Warranty Notification 29
- Claiming 30
- Conditions 31
- Installed Data 32
- Out of Warranty Repairs 32
- Revision History 33
- Revision History (Cont.) 34
- Version Date Issue Remarks 34
- Chapter 1: Product Features 35
- CSD Operation 36
- Improved OEM Features 37
- Set up Idle Mode Text 38
- Menu Selection 38
- Call Control by SIM 38
- TCP/UDP IP Connection 39
- Chapter 1: Product Features 41
- Online Data Mode 42
- Features and Benefits 43
- FTP Connection 44
- Manage FTP Connection 45
- Manage Remote File System 46
- File Transfer Operations 46
- Other FTP Operations 47
- Overview 48
- Suppression 49
- MUX Integration 50
- Technical Description 51
- Short Message Service (SMS) 52
- POP3 Email 54
- Character Sets 56
- AT Commands Summary 58
- AT Commands Overview 73
- AT Commands Protocol 74
- AT Commands Structure 75
- Results Code Structure 76
- Command Token Types 78
- Command Argument Types 79
- Command Mode Types 79
- Aborting Commands 80
- Core AT Commands 81
- +FTPCDUP 83
- +FTPCLOSE 83
- Modem ID 89
- Command Response/Action 91
- Table 3-2: +CSCS Parameters 93
- +CIMI, Request IMSI 94
- +CNUM, Request MSISDN(s) 95
- Read Command 96
- Table 3-3: +CNUM Parameters 96
- Capability Reporting 98
- Receiving a Data Call 100
- Call Control AT Commands 101
- DL, Dial Last Number 104
- H, Hang-up Call 105
- A, Answer Incoming Call 107
- Indication 107
- Table 3-7: +CRC Parameters 108
- RING/+CRING Indication 108
- Table 3-8: +CLIP Parameters 110
- +CCWA, Call Waiting Command 111
- Table 3-9: +CCWA Parameters 112
- Table 3-11: 115
- • Provisioned permanently 119
- Table 3-13: +CLIR Parameters 120
- &Q, Asynchronous Mode 123
- +CHUP, Hang Up Call 123
- Connection of a Voice Call 126
- Table 3-17: +MFIC Parameters 129
- +MHUP, Motorola Hung UP call 130
- AT+MTTY=? 133
- +MTTY: (0-3) 133
- AT+MTTY=1 133
- Call Status Messages 134
- +CLCC, List Current Calls 135
- Execute command enables 135
- Table 3-22: +CLCC Parameters 136
- +MCST, Call Status Messages 137
- +MCST Parameters 138
- Table 3-23: +MCST Parameters 138
- +TCLCC, List Current Calls 139
- Table 3-24: +TCLCC Parameters 140
- Table 3-25: +MNTFY Parameters 142
- +CAOC, Advice of Charge 143
- +CACM, Accumulated Call Meter 145
- Table 3-28: +CAMM Parameters 147
- +CR=[<mode>] OK 149
- +CR? +CR:<mode> 149
- +CR=? +CR:<mode> 149
- Supplementary Services 150
- Table 3-31: 151
- +CSSN Parameters 151
- Table 3-35: 155
- Table 3-36: +COLP Parameters 158
- Table 3-37: +CPBS Parameters 160
- +CSVM, Set Voice Mail Server 165
- Table 3-42: +MDSI Parameters 168
- Table 3-43: +MCSN Parameters 171
- +MDBR, Read Date Book Entries 177
- Table 3-47: +MDBR Parameters 178
- +MDBW, Write Date Book Entry 179
- Table 3-48: +MDBW Parameters 180
- Table 3-49: +MDBWE Parameters 182
- Table 3-50: +CCLK Parameters 185
- SMS Commands 186
- +CMGF, Message Format 189
- Table 3-54: + 190
- Table 3-55: +CSCA Parameters 191
- Table 3-56: +CSMP Parameters 192
- Table 3-58: +CSDH Parameters 194
- Indication) 198
- <Parameter> Description 201
- +CMGL, +MMGL, List Messages 202
- Table 3-65: 204
- +CGML/+MMGL Parameters 204
- +CMGR, +MMGR, Read Message 206
- Table 3-66: 207
- +CGMR/+MMGR Parameters 207
- GSM03.40) 209
- GSM03.40) (Cont.) 210
- Reserved bits are ignored 211
- Table 3-70: <fo> f 211
- +MMAR, Motorola Mark As Read 213
- +CMGD, Delete Message 220
- +CMGS, Send SM to Network 222
- Table 3-83: 226
- +MCSAT Parameters 226
- + MEDT? +MEDT: <mode> 228
- AT+MEDT=? +MEDT: (list of 228
- Table 3-84: +MEDT Parameters 229
- • SMS-DELIVER 231
- • SMS-STATUS-REPORT 231
- • CBM (broadcast message) 231
- DCS handling 233
- Examples: 235
- Email Services AT Commands 238
- Table 3-90: +MEMAS Parameters 240
- Table 3-91: +MEMGS Parameters 242
- Example: 243
- Table 3-92: +MEMDE Parameters 244
- +MEMSE, Send Email Message 245
- +MEML, List Email Messages 248
- +MEMR, Read Email Message 251
- +MEMD, Delete Email Message 252
- Table 3-97: +MEMD Parameters 253
- +MEGA, Email Gateway Address 255
- AT+MEGA? 256
- +MEGA: "4252833433" 256
- Network Commands 257
- +CRLP, Radio Link Protocol 258
- Table 3-102: +CREG Parameters 259
- +COPS, Operator Selection 262
- Table 3-104: +COPS Parameters 264
- +CPOL, Preferred Operators 265
- Table 3-107: +MFS Parameters 269
- Table 3-108: + 271
- MCELL Parameters 271
- Cell Resel 273
- T3212 Routing 273
- Multiband Reporting 273
- Cell Resel. offset MaxTxPow 275
- Table 3-123: 278
- EFEM Parameters 278
- Power offset in dBm 280
- Table 3-125: +MCI Parameters 284
- +MJDC, Jamming Detection 285
- Table 3-126: +MJDC Parameters 286
- Hardware Information 288
- +CBAUD, Baud Rate Regulation 289
- +MTDTR, DTR Line Test Command 292
- +MTCTS, CTS Line Test Command 293
- &K, RTS/CTS Flow Control 293
- &C, Circuit 109 Behavior 294
- &D, Circuit 108 Behavior 296
- +MCWAKE, GPRS Coverage 297
- ATS97, Antenna Diagnostic 301
- +MRST, Perform Hard Reset 302
- +TWUS, Wakeup Reason Set 302
- +TWUR, Wakeup Reason Request 304
- +TASW, Antenna Switch 304
- +MIOC, Motorola I/O Configure 308
- Table 3-143: + 309
- MIOC Parameters 309
- Light control example: 310
- +MIOD, Motorola I/O Define 312
- Table 3-144: + 313
- MIOD Parameters 313
- Table 3-145: Keypad GPIOs 313
- Table 3-146: +MMAD Parameters 316
- +MPCMC, Continuous PCM Clock 321
- Audio Setup 325
- Basic Audio Setup 326
- Advanced Audio Setup 326
- Basic Audio Setup Commands 327
- +CLVL, Loudspeaker Volume 328
- S94, Sidetone Effect 330
- S96, Echo Canceling 331
- +MAPATH, Audio Path 332
- Figure 3-7: Audio Paths 333
- +MAVOL, Volume Setting 335
- +MAMUT, Input Devices Mute 337
- +MAFEAT, Features Selection 338
- General Audio Commands 339
- +CALM, Alert Sound Mode 340
- +CRTT, Ring Type Selection 342
- Table 3-167: +CRTT Parameters 343
- +VTD, Tone Duration 345
- Access Control Commands 347
- Unblocking SIM Card 348
- Table 3-172: +CPIN Parameters 349
- +CPWD, Change Password 353
- +CLCK, Facility Lock 354
- Table 3-176: +CLCK Parameters 355
- Table 3-177: +EMPC Parameters 358
- Command 360
- Web-Session default entry 360
- Automatic/Non-Automatic 362
- New Bootstrap Process 368
- AT+MFOTABS OK 369
- +CME ERROR 369
- Modem Register Commands 370
- Q, Result Code Suppression 371
- E, Command Echo 372
- S, Bit Map Registers 374
- Table 3-188: S2 Parameters 376
- \G, Software Control 377
- \J, Terminal Auto Rate 377
- \N, Link Type 377
- +CBAND, Change Radio Band 377
- Sleep Mode Commands 379
- Sleep Mode AT Commands 380
- Sleep Mode HW Signals 380
- WAKEUP-IN 381
- Line (pin #16) 381
- Line (pin #21) 381
- Error Handling Commands 386
- Table 3-196: +CMEE Parameters 387
- Table 3-197: +CME Errors 388
- Table 3-198: +CM 390
- S Errors 390
- Table 3-199: +STK Errors 391
- +CEER, Extended Error Report 393
- Table 3-200: +CEER Parameters 394
- Table 3-201: + 397
- MGEER Parameters 397
- UI (User Interface) 399
- Table 3-202: +CRSM Parameters 400
- &V, View Configuration 404
- &W, Store User Profile 405
- AT&W0 406
- AT&W1 406
- &Y, Default User Profile 407
- +CKPD, Keypad Control 407
- +CME ERROR: <err> 408
- Table 3-208: +MKPD Parameters 410
- Table 3-209: +CMER Parameters 411
- +CLAN, ME Language 412
- +CIND, Indicator Control 413
- Table 3-211: +CIND Parameters 414
- +CKEV, Key Press Echo Output 417
- +MUPB, Phone Book Event 419
- GPRS/EDGE 420
- +CGDCONT, Define PDP Context 422
- For example: 423
- +CGATT, GPRS Attach or Detach 427
- Table 3-222: D*99 Parameters 430
- +CGPRS, GPRS Coverage 431
- CGPADDR, GPRS ADDResses 433
- +MDLC, Dial Local Connection 434
- +MIAU, IP Addresses Utility 435
- Table 3-226: +MIAU Parameters 436
- EDGE Commands 437
- Table 3-227: 440
- +CGEQREQ Command Parameters 440
- Table 3-228: 446
- +CGEQMIN Command Parameters 446
- +CGEQNEG - (Negotiated) 449
- Table 3-229: 450
- +CGEQNEG Command Parameters 450
- +MCEG, Motorola Control EGPRS 453
- Customer 454
- Application 454
- STK Mechanisms 455
- +MTKR, Profile Download 455
- Profile Structure 456
- Table 3-254: + 467
- Send DTMF 471
- Language Codes 476
- +MTKM, Motorola ToolKit Menu 480
- Control are modified 482
- Table 3-262: +MTKC Parameters 482
- Table 3-283 487
- +MIPCLOSE, Close a Socket 490
- +MIPSEND, Send Data 493
- +MIPSTAT, Status Report 498
- Pseudo-command Mode 499
- MIPXOFF, Flow Control - Xoff 499
- MIPXON, Flow Control - Xon 500
- • Power Up - 0 502
- Table 3-276: 505
- +MPING Command Parameters 505
- Table 3-278: 508
- +MSDNS, Set DNS IP Address 510
- Table 3-281: + 516
- MIPCFF Parameters 516
- Table 3-282: 518
- +MIPSSL Parameters 518
- Table 3-283: +MIPSSL Alerts 518
- FTP (File Transfer Protocol) 520
- +FTPMKD, Make Directory 526
- +FTPRMD, Remove Directory 527
- +FTPCDUP, Change Directory Up 529
- +FTPDEL, Delete File 529
- +FTPREN, Rename File 530
- +FTPLIST, Request List 532
- +FTPSTAT, Request Status 533
- +FTPNOOP, No Operation 536
- NOP - Compatible 540
- Fax Class 1 541
- Fax Commands 542
- +FTS, Transmit Silence 543
- +FRS, Receive Silence 543
- +FTM, Transmit Data 544
- +FRM, Receive Data 546
- +FRH = <MOD> CONNECT 548
- NO CARRIER 548
- +FPR, Fax Serial Port Rate 550
- RS232 Multiplexer Feature 552
- Product Architecture 553
- MUX States Overview 553
- PREMUX State 554
- UART Flow Control 555
- +CMUX, MUX Startup Command 556
- MUX Modes 557
- Basic MUX Channel Definitions 558
- Channel Priorities 558
- Two virtual channels– G24 559
- • PCHS: Per channel setting 560
- • PCHS: 560
- Unsolicited 569
- -special 569
- Multiple Channel Definitions 572
- GPRS Definitions 572
- Chapter 4: Using the Commands 575
- GPRS VoiceCSD Data 576
- G24 Network Connection 577
- Test G24 Communication 577
- G24 Phonebook Download 577
- Status (Optional) 577
- RS232 Lines Setup 578
- Basic Configuration 579
- 1. Baud setting example: 580
- AT+CPIN? 581
- See Developer’s Guide 581
- +CPIN: READY 581
- Terminal Synchronization 583
- Dialing Using ATD 588
- Voice Call Manipulations 590
- Conference Call 591
- Data Call 592
- Establishing GPRS PDP Context 593
- Using the ATD* Command Set 594
- Changing the Character Set 595
- Less then S24 596
- Get Inkey 597
- Get Input 598
- Play Tone 598
- Set Up Menu 599
- Select Item 599
- Send SMS 599
- Set Up Call 600
- Call Control 600
- Launch Browser 601
- Setup Event List 602
- TCP Data Transfer Example 603
- Xoff and Xon Example 605
- Terminal 607
- Handsfree 607
- (Non-Transparent Mode) 608
- Chapter 5: Tools 611
- Using WinFAX 612
- Appendix A: Reference Tables 613
- Functionality 635
- Symbol GSM (GSM 03.38) 645
- Appendix B: MUX 655
- MUX State 656
- MUX UART Port Speed 657
- MUX State Procedures 659
- UIH Frames 660
- Test UIH Control Frames 660
- MUX Customer Packet 661
- Mux 0710 Packet 662
- MUX Open Service 664
- MUX Close Service 664
- Data Transfer 664
- Acronyms and Abbreviations 665
- Abbreviation Full Name 667
- Numerics 671
- B - C Index 673
- H - M Index 675
- T - W Index 677
- @6889192V28@ 680
Produits connexes et manuels pour Mise en réseau Motorola AT Commands G24-L
(21 pages)
(13 pages)
(185 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels