Motorola CPCI-6115 Manuel de service Page 100
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CPCI-6115 CompactPCI Single Board Computer Installation and Use (6806800A68D)
Transition Module Preparation and Installation CompactPCI User I/O Connector
98
*Not connected on MXP version
5.5.4 CompactPCI User I/O Connector
Connector J5 is a 110 pin AMP Z-pack 2mm hard metric type B connector. This connector
routes the I/O signals for the PMC2 I/O signals, the IDE port, four asynchronous serial ports
and I2C. The pin assignments for J5 on the processor board and the CPCI-6115-MCPTM are
as follows:
(Outer row F is assigned and used as ground pins but is not shown in the table).
5 PMC1IO45 PMC1IO44 PMC1IO43 PMC1IO42 PMC1IO41 5
4 PMC1IO50 PMC1IO49 PMC1IO48 PMC1IO47 PMC1IO46 4
3 PMC1IO55 PMC1IO54 PMC1IO53 PMC1IO52 PMC1IO51 3
2 PMC1IO60 PMC1IO59 PMC1IO58 PMC1IO57 PMC1IO56 2
1 IPMI_PWR PMC1IO64 PMC1IO63 PMC1IO62 PMC1IO61 1
Signal Description
PMCIO:
PMC1IO(64:1) PMC1 I/O signals 1 through 64
Ethernet:
PORTn_TXP high side of differential transmit data
PORTn_TXN low side of differential transmit data
PORTn_RXP high side of differential receive data
PORTn_RXN low side of differential receive data
Table 5-7 User I/O Connector Pinout, J3 (continued)
Pin Row A Row B Row C Row D Row E Pin
Table 5-8 User I/O Connector Pinout, J5
PinRow ARow BRow CRow DRow EPin
22 DRESET_L COM4_TXD COM3_TXD COM2_TXD COM1_TXD 22
21 INTRQA COM4_RXD COM3_RXD COM2_RXD COM1_RXD 21
20 CS1FXA_L CS3FXA_L DA2 MXDI MXDO 20
19 Not Connected DIORDYA DA1 MXCLK MXSYNC# 19
18 DIOWA_L DA0 TMCOM1_L I2C_CLK I2C_DATA 18
17 GND DD14 DD15 DIORA_L Not Connected 17
16 DD9 DD10 DD11 DD12 DD13 16
15 DD5 DD6 GND DD7 DD8 15
14 DD0 DD1 DD2 DD3 DD4 14
13 PMC2IO5 PMC2IO4 PMC2IO3 PMC2IO2 PMC2IO1 13
- CPCI-6115 CompactPCI 1
- Single Board Computer 1
- Trademarks 2
- Contents 3
- List of Tables 10
- List of Figures 11
- About this Manual 13
- Abbreviations 14
- Conventions 16
- Summary of Changes 17
- Comments and Suggestions 18
- Safety Notes 19
- Operation 20
- Installation 20
- Cabling and Connectors 21
- Environment 22
- Sicherheitshinweise 23
- Schaltereinstellungen/Jumper 24
- Kabel und Stecker 26
- Umweltschutz 26
- Batterie 26
- Introduction 27
- 1.2 Standard Compliances 28
- 1.3 Ordering Information 29
- 2.1 Overview 31
- Requirements 32
- 2.3.2 Power Requirements 34
- 2.3.3 Thermal Requirements 34
- 2.4 Getting Started 37
- 2.5 Baseboard Preparation 38
- 2.5.3 J6, Bus Mode Selection 40
- 2.5.7 J20, Safe Start Header 42
- 2.6 Operating Modes 44
- 2.7 Installing Hardware 44
- Procedure 45
- Personal Injury or Death 46
- 2.9 Applying Power 49
- 3.1 Overview 51
- 3.2 Board Layout 52
- 3.4 ABORT/Reset Switch 54
- 3.5.7 CompactPCI Connector 58
- PCI_RSVD = PCI Reserved pin 62
- 3.5.14 Safe Start Header 67
- 3.5.15 Bus Mode Select Header 67
- 3.5.18 +/-12 V Present Header 68
- Functional Description 69
- 4.2 Block Diagram 70
- 4.3 General Description 71
- 4.3.2 Processor 72
- 4.3.3 L3 Cache 72
- 4.3.4.12 Interrupt Controller 76
- 4.3.4.13 PCI Bus Arbitration 76
- 4.3.4.14 Board Reset Logic 77
- 4.3.5 System Memory 81
- 4.3.6 Flash Memory 82
- 4.3.8 TL16C550C UART Devices 83
- 4.3.9 System Registers 83
- 4.3.10 Serial EEPROM Devices 83
- 4.3.11 PCI Bus 0.0 83
- 4.3.12 PCI Bus 1.0 83
- 4.3.13 IDE Controller 84
- 4.3.15 CompactPCI Bus 84
- 4.3.16 PMC Slots 84
- 4.4 Miscellaneous 86
- 4.4.3 Onboard Power Supplies 89
- 4.4.4 Hot Swap Support 89
- 4.4.5 Hot Swap Process 89
- 5.2 Block Diagram 92
- 5.4 Rear Panel Connectors 94
- 5.5.2.1 Host IO Connectors 96
- 5.5.2.2 PMC I/O Connectors 98
- 5.6 Jumper Settings 104
- 5.7 Functional Description 105
- 5.7.3 Hot-Swap Support 106
- 5.7.4 Serial EEPROM 106
- 5.7.5 PMC I/O Modules 106
- 5.7.7 PMC I/O Module 110
- 5.7.9 PMC I/O Connector 112
- 5.7.10 Host I/O Connector 112
- 5.8 Installing the PIM 113
- Figure 5-9 Installing the PIM 114
- Remote Start via the PCI Bus 117
- MOTLoad Firmware 119
- 7.4 MOTLoad Commands 120
- 7.6 MOTLoad Tests 120
- 7.7 Using MOTLoad 121
- 7.7.2 Command Line Help 122
- 7.7.3 Command Line Rules 122
- 7.8 MOTLoad Command List 123
- Memory Maps 127
- 8.2.2 Processor Memory Map 128
- 8.2.3 Default PCI Memory Map 129
- 8.2.5 System I/O Memory Map 131
- 8.2.7 CompactPCI Memory Map 131
- 8.2.9 L1, L2 and L3 Cache 132
- 8.2.10 System Memory 132
- A Related Documentation 133
- A.3 Related Specifications 134
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(25 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.780 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels