Motorola Phaser P460 Instructions d'exploitation Page 71
- Page / 208
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-12
P460/P360 Memory Scanners Product Reference Guide
Host Type
RS-232 Host Types
Most RS-232C hosts work fine with the default settings, however, three RS-232C hosts are
set up with their own parameter default settings. Selecting the ICL, Fujitsu or Nixdorf RS-
232C host interface sets the defaults listed below. These defaults take precedence over
Standard RS-232 defaults. So, if you select the Fujitsu RS-232C first, and then select
the Standard RS-232 defaults, the Fujitsu defaults still take precedence. To return to
the factory set defaults, scan the SET ALL DEFAULTS bar code on page 5-9.
Table 5-2. Terminal Specific RS-232C
Parameter Standard ICL FUJITSU NIXDORF
Mode A/
Mode B
Transmit Code ID No Yes Yes Yes
Data Transmission Format Data as is Data/Suffix Data/Suffix Data/Suffix
Suffix CR/LF CR CR CR
Baud Rate 9600 9600 9600 9600
Parity None Even None Odd
Hardware Handshaking None RTS/CTS
Option 3
None RTS/CTS
Option 3
Software Handshaking None None None None
Serial Response Time-out 2 Sec. 9.9 Sec. 2 Sec. 9.9 Sec.
Stop Bit Select One One One One
ASCII Format 8-Bit 8-Bit 8-Bit 8-Bit
Beep On <BEL> Disabled Disabled Disabled Disabled
RTS Line State Low High Low *Low = No
data to send
*In the Nixdorf Mode B, if CTS is Low, transmission of scan data is disabled. When CTS is High,
bar code data is transmitted to the host.
- P460/P360 Memory 1
- Scanners 1
- Product Reference Guide 1
- P460/P360 Memory Scanners 2
- Contents 4
- Chapter 3. Operation 5
- Chapter 5. Parameter Menus 6
- Feedback 9
- About This Manual 10
- Related Publications 11
- Service Information 11
- Symbol Support Center 12
- Warranty 14
- Chapter 1 16
- The Phaser Series Scanner 16
- The Cradle 17
- Chapter 2 20
- Setting Up the Cradle 22
- Scanner Power Options 23
- Charging the Battery 23
- Battery Charge 24
- Connecting to a Host 24
- Adapter Cable 25
- Flying Power Lead 25
- To Cradle 25
- Chapter 3 28
- Operation 28
- Initial Powerup 29
- Batch / Inventory Application 29
- Numeric Data Entry 30
- Alpha Data Entry 30
- Quantity: _____ 31
- CODE: xxxx 31
- aaaa/bbbb 31
- Transmitting Data to the Host 32
- Daisy-Chaining Cradles 33
- Scan and Transmit Application 33
- System Menu 34
- System Setup 35
- App. Control 36
- Parameter Control 39
- System Status 39
- ADF Plus 40
- Scanning 41
- Right Wrong 42
- Te s t S y m b o l s 43
- Symbol Technologies, Inc 44
- Depth of Field 46
- Keypad Operation 48
- Troubleshooting 50
- You Should 51
- Chapter 4 52
- Replacing the Battery 53
- Accessories 54
- Technical Specifications 55
- Pin-outs 57
- Table 4-5. Scanner Pin-outs 58
- Beeper Indications 59
- Chapter 5 60
- Table 5-1. Default Tabl e 61
- Set Default Parameter 68
- Communication Protocol 69
- Batch/Inventory Application 70
- Host Type 71
- Sleep Time 74
- Date Separator 75
- Hour Type 76
- Decimal Separator 77
- Date Format 78
- Key Click 79
- Laser On Time 80
- Scan Stand Options 81
- Timeout Between Decodes 82
- The Same Symbol 82
- Different Symbols 82
- Beeper Options 84
- Beeper Volume 85
- Power Detect Beep 86
- Beep After Good Decode 87
- Decode Options 88
- Enable/Disable EAN-8/EAN-13 90
- Enable/Disable Bookland EAN 91
- Decode UPC/EAN Supplementals 92
- DECODE UPC/EAN 93
- SUPPLEMENTAL REDUNDANCY 93
- UPC-E, or UPC-E1 check digit 94
- UPC-A Preamble 95
- UPC-E Preamble 96
- UPC-E1 Preamble 97
- Convert UPC-E to UPC-A 98
- Convert UPC-E1 to UPC-A 99
- EAN Zero Extend 100
- Convert EAN-8 to EAN-13 Type 101
- UPC/EAN Coupon Code 102
- Enable/Disable Code 128 103
- Lengths for Code 128 104
- Enable/Disable UCC/EAN-128 104
- Enable ISBT 128 105
- Disable ISBT 128 105
- Enable/Disable Code 39 106
- ENABLE TRIOPTIC CODE 39 107
- DISABLE TRIOPTIC CODE 39 107
- Set Lengths for Code 39 108
- CODE 39 - LENGTH WITHIN RANGE 109
- CODE 39 - ANY LENGTH 109
- Parameter Menus 110
- ENABLE CODE 39 CHECK DIGIT 110
- DISABLE CODE 39 CHECK DIGIT 110
- Transmit Code 39 Check Digit 111
- ENABLE CODE 39 FULL ASCII 112
- DISABLE CODE 39 FULL ASCII 112
- Convert Code 39 to Code 32 113
- Code 32 Prefix 114
- Enable/Disable Code 93 115
- Set Lengths for Code 93 116
- CODE 93 - LENGTH WITHIN RANGE 117
- CODE 93 - ANY LENGTH 117
- ENABLE INTERLEAVED 2 OF 5 118
- DISABLE INTERLEAVED 2 OF 5 118
- I 2 of 5 - ANY LENGTH 120
- USS CHECK DIGIT 121
- OPCC CHECK DIGIT 121
- Transmit I 2 of 5 Check Digit 122
- Convert I 2 of 5 to EAN-13 123
- ENABLE DISCRETE 2 OF 5 124
- DISABLE DISCRETE 2 OF 5 124
- D 2 of 5 - ANY LENGTH 126
- Enable/Disable Codabar 127
- Set Lengths for Codabar 128
- CODABAR - LENGTH WITHIN RANGE 129
- CODABAR - ANY LENGTH 129
- CLSI Editing 130
- NOTIS Editing 131
- Enable/Disable MSI Plessey 132
- Set Lengths for MSI Plessey 133
- MSI PLESSEY - ANY LENGTH 134
- MSI Plessey Check Digits 135
- (ENABLE) 136
- (DISABLE) 136
- MOD 10/MOD 11 137
- MOD 10/MOD 10 137
- Enable/Disable PDF417 138
- PDF417 Scanning Mode 139
- Raster Height (Default 15) 140
- (Continued) 141
- Aiming Mode 142
- Enable/Disable MicroPDF 143
- Code 128 Emulation 144
- UCC/EAN-128 Emulation 145
- Macro PDF Features 146
- Transmit Unknown Codewords 150
- Escape Characters 151
- Delete Character Set ECIs 152
- ECI Decoder 153
- Transmit File Name 154
- Transmit Block Count 155
- Transmit Time Stamp 155
- Transmit Sender 156
- Transmit Addressee 156
- Transmit Checksum 157
- Transmit File Size 157
- Last Blocker Marker 158
- Flush Macro Buffer 159
- Abort Macro PDF Entry 159
- Security Options 160
- Linear Security Level 3 161
- Linear Security Level 4 161
- Bi-directional Redundancy 162
- UPC/EAN Security Level 163
- UPC/EAN Security Level 2 164
- UPC/EAN Security Level 3 164
- RS-232C Parameters 165
- Baud Rate (Continued) 166
- Check Receive Errors 168
- Hardware Handshaking 169
- STANDARD RTS/CTS 170
- RTS/CTS OPTION 1 170
- Software Handshaking 171
- ACK/NAK with ENQ 172
- Host Serial Response Time-out 173
- RTS Line State 174
- Stop Bit Select 175
- ASCII Format 175
- Beep on <BEL> 176
- Intercharacter Delay 176
- MCL-Net Parameters 177
- MCL-Net Baud Rate (Continued) 178
- MCL-Net Hex Addressing Mode 179
- Scanner Address 179
- MCL-Net Transmit Retries 180
- MCL-Net Frame Timeout 180
- Numeric Bar Codes 181
- Numeric Bar Codes (Continued) 182
- Appendix A 184
- Bar Code Information 184
- AIM Code Identifiers 186
- Appendix B 196
- Messages and Error Codes 196
- Tell Us What You Think 206
- 70-37690-02 208
- Revision A — June 2001 208
Produits connexes et manuels pour Lecteurs de codes-barres Motorola Phaser P460
(2 pages)
(36 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.467 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels