Motorola Laptop IH5 Manuel d'utilisateur Page 41
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hardware Installation
http://www.motorola.com/computer/literature 1-21
1
Hardware Installation
The following sections discuss the placement of PMC mezzanine cards on
the MCPN750A baseboard and the installation of the complete
MCPN750A assembly into a CompactPCI chassis. Before installing the
MCPN750A, ensure that all header jumpers are configured as desired.
In most cases, PMC modules ordered with the baseboard are installed on
the MCPN750A at the factory and the order is shipped as a single unit. The
user-configured jumpers on the PMCs are accessible with the mezzanines
installed.
If it is necessary to install mezzanines on the baseboard, refer to the
following sections for a brief description of the installation procedure.
Note: the procedure assumes the MCPN750A has already been installed in
the chassis. If not, begin with Step 4.
!
Caution
Avoid touching areas of integrated circuitry; static discharge can damage
these circuits.
Installing PMC Modules on the MCPN750A SBC
One dual wide, one single wide or two single wide PCI mezzanine (PMC)
modules can be mounted on top of the MCPN750A baseboard. The
MCPN750A is designed to accept only +5V or Universal PMCs. Due to
pin current limitations, the MCPN750A can supply up to 4.5 amps to a
single PMC on each of the +3.3V and +5V supplies. The MCPN750A can
supply a maximum of 500mA at +12V and -12V to each PMC. Refer to the
table on page 1-31 for the total current available to PMC’s and transition
modules. To install a PMC module, refer to Figure 1-9 PMC Carrier Board
Placement on MCPN750A, and proceed as follows:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD
strap to the chassis as a ground. The ESD strap must be secured to
your wrist and to ground throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power
off and remove the AC cord or DC power lines from the system.
- Installation and Use 1
- Safety Summary 3
- Flammability 4
- EMI Caution 4
- Lithium Battery Caution 4
- Contents 7
- List of Figures 13
- List of Tables 15
- About This Manual 17
- Summary of Changes 18
- Overview of Contents 18
- Comments and Suggestions 19
- 1Hardware Preparation and 21
- Installation 21
- 66MHz PPC603 Processor 22
- 33MHz 32/64-bit CompactPCI 22
- Getting Started 23
- Equipment Required 24
- Unpacking Instructions 25
- ESD Precautions 25
- Preparation 26
- System Considerations 30
- 2286 9806 32
- 2362 9808 34
- 2363 0001 40
- Hardware Installation 41
- 2288 9806 42
- 2695 0001 47
- 2Startup and Operation 53
- 11734.00 9702 54
- Memory Maps 55
- PCI Local Bus Memory Map 56
- CompactPCI Memory Map 57
- L2 Cache 58
- System Clock Generator 58
- PPC Bus Arbitration 58
- PCI Host Bridge 58
- PCI Arbitration 60
- Interrupt Handling 60
- ISA DMA Channels 61
- Sources of Reset 61
- Startup and Operation 62
- Endian Issues 64
- PPCBug Overview 67
- PPCBug Basics 67
- Diag> 68
- Memory Requirements 69
- PPCBug Implementation 69
- Using PPCBug 71
- Debugger Commands 72
- Table 3-1. Debugger Commands 73
- Diagnostic Tests 76
- PPC1-Bug> 77
- PPC1-Bug> prompt 77
- PPC1-Diag> 77
- 4CNFG and ENV Commands 79
- CNFG and ENV Commands 80
- ENV - Set Environment 81
- (Default) 87
- 5Remote Start Via the PCI Bus 91
- Opcode 0x04: Checksum Memory 96
- Opcode 0x06: Debugger Query 97
- Opcode 0x07: Execute Code 97
- Remote Start Via the PCI Bus 100
- MCPN750A (target) Console 101
- Introduction 103
- 6Functional Description 105
- General Description 106
- Block Diagram 107
- Functional Description 108
- CompactPCI Bus Interface 109
- Ethernet Interface 110
- PCI Mezzanine Interface 111
- ISA Bus Devices 112
- Serial EEPROM 112
- Hot Swap Control Circuitry 118
- Programmable Timers 118
- MPC750 Processor 124
- ECC Memory Controller 126
- DRAM Memory 126
- Compact FLASH Memory Card 126
- TMCPN710 Transition Module 127
- TM-PIMC-0001 127
- 7Connector Pin Assignments 129
- BRSVP2B18 131
- BRSVP2C18 131
- BRSVP2B16 132
- MCPN750A Connector J4 134
- Connector Pin Assignments 136
- J13/23, J14/24) 137
- Same as above 149
- Connector (J13) 150
- (J15, J16) 151
- Connectors (J12 & J13) 158
- Connector (J7) 159
- Connector (J1) 159
- J20, and J14/J24) 161
- ASpecifications 167
- Cooling Requirements 168
- EMC Compliance 169
- Specifications 170
- BRelated Documentation 171
- Manufacturers’ Documents 172
- Related Specifications 174
- http://www.eia.org/ 175
- http://www.picmg.com/ 176
- Numerics 177
Produits connexes et manuels pour Processeurs Motorola Laptop IH5
Processeurs Motorola MVME1X7P Manuel de service
(108 pages)
(108 pages)
Processeurs Motorola CPU32 Manuel d'utilisateur
(646 pages)
(646 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.543 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels