Motorola CPCI-6115 Manuel de service Page 15
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CPCI-6200 Installation and Use (6806800J66C)
15
About this Manual
Overview of Contents
This manual is divided into the following chapters and appendices.
Introduction provides an overview of the features of the product, including ordering and
other product information like the location of labels.
Hardware Preparation and Installation discusses procedures on installing the CPCI
baseboard, PMC modules, and other accessories.
Controls, LEDs, and Connectors provides information on connector pinouts and board and
front panel layouts.
Functional Description discusses the main functional blocks on the product.
MOTLoad Firmwareprovides an overview and description of basic MOTLoad use including
implementation issues, a list of the initialization sequence, and a description of basic
commands.
Control via IPMI discusses the IPMI commands that the product supports.
Memory Maps and Addresses provides details on the various registers and addresses used in
the product.
Replacing the Battery provides instructions on how to replace the onboard battery.
Related Documentation provides a list of documentation relevant to the product.
Safety Notes lists the safety notes applicable to the product.
Sicherheitshinweise lists the German version of the safety notes.
Abbreviations
This document uses the following abbreviations:
Abbreviation Definition
ANSI American National Standard Institute
BMC Base Board Management Controller
CE Chip Enable
COM Communications
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(174 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.299 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels