Motorola CPCI-6115 Manuel de service Page 91
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Functional Description
CPCI-6200 Installation and Use (6806800J66C)
91
4.17 RTC Battery
The CPCI-6200 provides onboard battery clips for holding a coin cell type battery. The clips
allow for the quick and easy replacement of a 3 V button cell lithium battery (CR2430), which
provides back-up power to the onboard M41T83 real-time clock (RTC). A battery switching
circuit that is built into the RTC provides automatic switching between the 3.3 V and battery
voltages. The battery is capable of providing backup power to the RTC for up to 12 years at
nominal temperature.
For information on replacing the battery, see Replacing the Battery on page 179.
4.18 IPMI Controller
The CPCI-6200 uses the Renesas 16-bit microcontroller H8S/2166 as IPMI controller. The
controller has the following features:
115 I/O ports
Eight-channel analog-to-digital converter
Six I
2
C bus
Three serial ports
512 KB flash memory
40 KB SRAM
USB
3
PCI4_RST_N Tsi381 1 ms 1.35 ms
CPCI
Backplane
Reset
3
PCI_BP_RST_N CPCI CPLD 1 ms 1.35 ms
Flash A
1
FRESET_N Reset CPLD 500 ns 125 μs
1. With MotLoad reset command
2. PCI Specification
Table 4-5 Reset Timing Requirements (continued)
Device Reset Signal Source of Reset
Minimum Reset
Time
Actual Reset
Time
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Produits connexes et manuels pour Commutateurs de réseau Motorola CPCI-6115
(174 pages)
(31 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.746 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels